LG Electronics Garage Door Opener AN MR400 User Manual

OWNER’S MANUAL  
Magic Remote  
Please read this manual carefully before operating your set and retain it  
for future reference.  
AN-MR400  
Remote control (AN-MR400G)  
RF Dongle (AN-MR400D)  
(Brazil : www.lge.com)  
 
3
* To avoid wireless interference, keep the distance  
between the Wi-Fi dongle and the remote RF  
RF DONGLE  
dongle over 20 cm.  
LA97**/ LA96**/ LA88**/ LA86**/ LA79**/  
LA74**/ LA71**/ LA69**/ LA68**/  
LA66**(LA6600 Except for Korea) /  
LA64**(Japan, Asia, Austrailia, Middle East, Africa)  
/ LA6250(Korea) / LA6205(Brazil, Mexico,  
USA, Canada) / LA620*(Japan, Asia, Austrailia  
, Middle East, Africa) / LN6100(Middle East,  
Africa) / LN5750(Brazil, Mexico, USA, Canada),  
LN570*(Korea, Except for 32LN570*)/  
LN570*(Middle East, Africa)/ LN578*(Europe)/  
PH67**/ PH66** / PH47** models do not require RF  
dongle connection. RF Dongle is built in TV.  
Cable IN  
RF SPECIFICATION  
The Magic Remote Control communicates with  
the RF Dongle using Bluetooth Version 3.0 .  
REV.5  
Output Power (Max.) : 10 dBm or lower  
Lamp  
Maximum Communication Distance :  
Line of Open Sight approx. 10 m  
INSTALLING THE RF DONGLE  
Image shown may differ from your TV.  
Frequency Range :  
2.400 GHz - 2.4835 GHz  
1 Locate the designated Velcro attachment  
location on the TV. Then tear off the protection  
paper and attach the Velcro. (The attachment  
location is different depending on the TV model  
you own)  
Data Rate (Max.) : 3 Mbps  
2 Connect the RF Dongle Cable plug on the RF  
Dongle to a USB or USB Apps jack on the TV.  
PRECAUTIONS TO TAKE  
Use the remote control within the specified  
range (within 10 m).  
You may experience communication failures  
when using the device outside the coverage area  
or if there are obstacles within the coverage  
area.  
Velcro  
You may experience communication failures  
depending on the accessories.  
Devices such as a microwave oven and wireless  
LAN operate in the same frequency band (2.4  
GHz) as the Magic Remote Control. This may  
cause communication failures.  
*Attach the RF Dongle aligning with the upper left  
corner bracket.  
3 Attach the RF Dongle to the velcro as shown  
above and then turn on the TV.  
The Magic Remote Control may not work  
properly if a wireless router (AP) is within 1  
meter of the TV. Your wireless router should be  
more than 1 m away from the TV.  
4 Turn your TV on and wait 20 seconds. Now,  
register the Magic Remote Control with your TV.  
* If the RF Dongle for the wireless media box is  
attached, attach the RF Dongle for the Magic  
Remote Control on the below right of the back of  
the TV.  
Do not disassemble or heat the battery.  
Do not drop the battery. Avoid avoid extreme  
shocks to the battery.  
Inserting the battery the wrong way may result in  
explosion.  
 
4
REGISTERING  
HOW TO USE  
To use the Magic Remote Control, pair it with  
your TV first.  
How to register the Magic  
Remote Control  
1 Put batteries into the Magic Remote  
Control and turn the TV on.  
2 Point the Magic Remote Control at  
your TV and press the WHEEL (OK)  
on the remote control.  
* If the TV fails to register the Magic  
Remote Control, try again after  
turning the TV off and back on.  
How to Re-register the Magic  
Remote Control  
Press the BACK and SMART  
at  
the same time, for five seconds, to  
unpair the Magic Remote Control  
with your TV.  
If you wish to re-register the remote,  
press the WHEEL (OK) on the remote  
control.  
VPDUW  
* Shake the Magic Remote Control slightly to the right  
and left or press SMART , , /Q.MENU buttons to make  
the pointer appear on the screen.  
* Shake the Magic Remote Control slightly to the right  
and left to make the pointer appear on the center of  
screen.  
* If the pointer has not been used for a certain period of  
time, it will disappear.  
* The wheel also functions as the ‘OK’ button when  
pressed.  
* You can change channels and scroll through menus  
using the Wheel.  
* You can just move your wrist to move the pointer  
instead of moving your whole arm.  
* The Magic Remote Control depletes batteries faster  
than a normal remote due to the additional features.  
You may wish to use rechargeable batteries.  
* If the pointer loses its calibration, set down the remote  
for a couple of minutes to let it recalibrate.  
 
 

Lenmar Enterprises Camera Accessories Digital Camera Batteries User Manual
Lenoxx Electronics Cassette Player 9190M User Manual
Lexmark All in One Printer X4270 Series User Manual
LG Electronics Cell Phone VX60001 User Manual
LG Electronics Refrigerator LFX21976ST User Manual
Life Fitness Treadmill 97twez User Manual
Logitech Computer Keyboard 920 002836 User Manual
Makita Grinder 9556HN User Manual
Makita Impact Driver XDT09 User Manual
Maxon Telecom Car Stereo System SM 2000 User Manual