Lennox Hearth Door 38LSBF User Manual

FIREPLACE KITS  
AND ACCESSORIES  
750,108M  
07/2001  
BI-FOLD GLASS DOORS  
INSTALLATION INSTRUCTIONS FOR LENNOX'S SYMPHONY SERIES BI-FOLD GLASS DOORS  
MODELS 38LSBF, 38LSBF-B, 43LSBF, 43LSBF-B, 48LSBF, 48LSBF-B  
GENERAL INFORMATION  
This door assembly consists of a right and left bi-fold glass panel  
assembly factory mounted within an outer frame. Door handles are  
attached in place. There are no additional parts that are required to  
install the Symphony Series door, all required hardware is provided.  
Fireplaces listed on the front page of this document, have been designed  
to accept the Symphony Series doors with minimum effort.  
TOOLS REQUIRED  
Medium Phillips Screwdriver  
Hammer  
Electric Drill  
⁵⁄₆₄" Diameter Drill Bit  
Note: In most cases the door frame will not install completely flush with  
theappliancefrontface. Theframewillusuallyprotrudefromtheopening  
approximately an 1/8 of an inch.  
Model LBR and LBC Fireplaces  
Note: The Center Wedge Clip located inside the track in the center of the  
door frame indicates the bottom of the frame. It is important that the  
frame be installed with the correct side up to insure smooth operation  
Lennox's Estate 48 fireplace may be fitted with either 48LSBF or  
48LSBF-B doors.  
of the doors.  
Step 1. Position the door support bracket along the lower front face of  
the appliance ash lip, oriented as shown (see Figure 1 ) (DO NOT affix the  
door support bracket to the outer front face of the appliance). Using the  
two (2) self tapping screws provided, secure the door support bracket  
to the front of the ash lip.  
Use Lennox's 38LSBF and 43LSBF with the LBR and LBC 3824 appli-  
ances and the LBR and LBC 4324 appliances respectively.  
Lennox's Symphony series Bi-Fold doors come standard with a decora-  
tor satin black finish and may be purchased in a polished brass finish  
designated by the -B suffix to the model/size number.  
Step 2. Position the frame in the fireplace opening on top of the door  
support bracket, centering left and right. Mark the fireplace at each hole  
in the side panels.  
Do not alter or modify these door assemblies or a fireplace malfunction  
or a fire hazard may result.  
Note: Theframeisprovidedwithtwosetsofholesallowingfornear"Flush  
Face" installation and "Protruding" installations that may be particularly  
useful in certain finish applications. In most cases the door frame will not  
install completely flush with the appliance front face. The frame will  
usually protrude from the opening approximately an 1/8 of an inch.  
These glass door assemblies have been tested and listed by Warnock  
Hersey Inc.  
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
 
ADJUSTMENT FOR DOOR ALIGNMENT  
The doors are properly adjusted when the top door trim is in a straight,  
level line and the gap between the doors and the frame is even at the top  
and bottom. The doors can be adjusted by changing the location of the  
door inside the frame. The door may need adjustment for several  
reasons. One would be that the doors do not fully close because they hit  
in the center of frame. Another would be that there is a noticeable gap  
in the center between the closed doors.  
Fully Open or  
Fully Closed  
Front-Open Systems  
If doors appear to close in correct position but do not latch (both doors  
do not stay closed), then there is a misalignment between the doors and  
the Center Wedge Clip. The Center Wedge Clip is located in the center  
of the bottom Track. In order to stay closed, the left and right doors must  
meet in the Middle of the Center Wedge Clip.  
Figure 4  
CLEANING  
NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT. DO NOT USE  
AMMONIAORANYAMMONIABASEDGLASSORHOUSEHOLDCLEANER  
TO CLEAN THE GLASS OR THE DOOR FRAME. AN AMMONIA BASED  
CLEANER WILL DAMAGE THE FINISH.  
To adjust doors, first loosen, but DO NOT remove the Phillips Screw that  
holds the Retainer Clip to the frame. Move door to desired position then  
tighten screw. Repeat procedure for other Retainer Clips as needed.  
Operate doors to check alignment and repeat procedure if necessary.  
Remove dirt and grime from the doors using a clean dampened towel  
followed by wiping with a dry towel. To remove stubborn stains from the  
doors, use a mild soap solution and towel to gently scrub away stain.  
Take care not to scratch the glass surface. Do not use abrasive cleaners.  
GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS  
CAUTION: THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH  
THE LENNOX FIREPLACE OR APPLIANCE MODELS SHOWN. USE ON  
ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTITUTE A POTEN-  
TIAL FIRE HAZARD.  
IMPORTANT  
These glass doors utilize tempered glass which is designed for use  
with high temperatures but can unexpectedly shatter. DO NOT SIT  
CLOSE TO THE GLASS.  
Avoid building extremely large fires as the tempered glass could  
become damaged.  
Use fireplace tools carefully to avoid striking the glass.  
Tempered glass will break into small particles if it should shatter  
unexpectedly. If the glass breaks, particles of extremely hot glass could  
be discharged into the surrounding environment, thereby creating a risk  
ofpersonalinjuryorfire. Observationoftheaboveoperatingprecautions  
and instructions will reduce the risk of personal injury or fire.  
Keep wire mesh screens closed during fireplace use.  
The fireplace flue damper must remain open until fire is completely  
out.  
Extreme temperature changes can cause breakage — do not build a hot  
fire and close the doors if the doors are cold.  
Assure wood and embers are well within the confines of the grate area  
and well away from the glass doors.  
If the tempered glass pane becomes scratched or chipped, it creates a  
weakness in the glass which can cause the glass to break when heated.  
Replace the pane of glass by contacting your nearest distributor. For the  
name of your nearest distributor contact:  
Keep wire mesh screens closed during fireplace use.  
Keep glass doors closed at night when retiring to minimize the loss of  
heated room air up the vent.  
LENNOX HEARTH PRODUCTS  
1110 West Taft Avenue  
Orange, CA 92865  
CAUTION: THE FRONT-OPEN FIREPLACE OR APPLIANCE SHOULD  
ONLYBEOPERATEDWITHTHEGLASSDOORSFULLYOPENORFULLY  
CLOSED (SEE FIGURE 4 ).  
CAUTION: GLASS AND METAL FRAMES GET HOT — ALWAYS USE  
HANDLES TO OPEN AND CLOSE THE DOORS.  
WARNING: DO NOT BURN TRASH, CONSTRUCTION SCRAPS,  
RAILROAD TIES, OR OTHER HIGHLY-FLAMMABLE MATE-  
RIAL IN THE FIREPLACE. INTENSE HEAT CAN CAUSE THE  
GLASS TO LOSE STRENGTH AND RESILIENCE WHICH WILL  
RESULT IN GLASS BREAKAGE.  
To remove the doors, open door all the way until glass panes are back  
to back. While pushing down on door, push up on Top Retainer Clip with  
finger to free Top Pin and rotate top of door toward center of frame.  
Carefully remove door.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
3
 
LENNOX reserves the right to make changes at any time, without notice, in design,  
materials, specifications, prices and also to discontinue colors, styles and products.  
Consult your local distributor for fireplace code information.  
Printed in U.S.A. © 2001 by LENNOX  
1110 West Taft Avenue  
Orange, CA 92865  
P/N 750,108M REV. N/C 07/2001  
 

Lenoxx Electronics Air Cleaner PMAC 12C User Manual
LevelOne Network Card FSW 1620TX User Manual
LG Electronics Speaker System LAP340 User Manual
Lincoln Electric Welding System GX 271 User Manual
Magma Computer Hardware PCI Expansion System User Manual
Magnavox Portable CD Player AZ 2407 User Manual
Makita Trimmer UML03D User Manual
Maytag Microwave Oven MMV5208 User Manual
Maytag Refrigerator W10289680A User Manual
Maytag Washer MAH2400AWW User Manual