Linear Turntable at fst User Manual

Lightweight Removable Control  
Mechanism  
Field Changeable for Fail Safe  
or Fail Secure Operation  
Outdoor Rated & Easy to Assemble  
Linear Action Centering  
Shock Absorption at all Impact  
Points  
Hinge Door Service Access  
Large Block Terminals for Field  
Connections  
1-1/8” thick Hard Coated Ratchets  
with 1” thick Hard Coated Pawls  
Now Part of  
Full Height Galvanized Steel  
Turnstile Series  
AT-FST Series  
The AT-FST full height galvanized steel turnstile series provides superior access  
control through solid construction and safe design. These units are rated for outdoor  
use and are hot dip galvanized finish.  
This unit was developed with the installer in mind and can be assembled in a fraction  
of the time it takes to install comparable industry models. Should requirements  
change after installation, a user can easily change these units (that come electrically  
pre-configured) from fail-safe to fail-secure.  
To prevent shock and vibration from transferring through the turnstile frame, all  
areas where mechanical impact occurs during normal operation (ratchets and  
mechanism mounts) are insulated with shock absorbing materials. This unique  
design assures a quiet and smooth operation of the turnstile and adds to the life of  
all mechanical parts.  
Linear does not charge extra for safety! Included with every turnstile are the  
following safety features: Heel protection, Home Position centering of spindle and  
Relocking timer.  
 
Easy access to the operating mechanism, control board(s) and other components located in the header area  
is accomplished through hinged panel doors that are key lockable. All bearings are permanently lubricated  
requiring no scheduled maintenance. The lower spindle bearing is located inside the spindle column and will  
not be exposed to salt, sweep cleaners or other floor maintenance materials that could cause failure. All shafts  
and hardware are made from stainless steel.  
d e f i n i T i O n s :  
1. Fail-Safe: Upon loss of electrical power the turnstile center spindle will rotate freely in the entrance or exit direction  
that is selected with this option from the ORDERING GUIDE.  
2. Fail-Secure: Upon loss of electrical power the turnstile center spindle will remain locked in the entrance or exit  
direction that is selected with this option from the ORDERING GUIDE.  
3. Locked: The center spindle will always be locked in the entrance or exit direction that is selected with this option  
from the ORDERING GUIDE.  
4. Manual: The center spindle will always freely rotate in the entrance or exit direction that is selected with this option  
from the ORDERING GUIDE.  
c a u T i O n :  
For safety reasons do not combine electrically controlled and manually controlled on the same center spindle.  
aT-fsT series (single) - dimensiOnal drawings  
60  
152.4  
53  
134.6  
in  
cm  
Header & Cover  
10  
25.4  
Spindle Arm Section  
Passage Panel  
(1 of 3 shown)  
80  
203.2  
Barrier  
in  
cm  
 
aT-fsT series (dOuble) - dimensiOnal drawing  
96  
243.8  
53  
134.6  
in  
cm  
Header & Cover  
10  
25.4  
Spindle Arms  
80  
203.2  
Barrier  
Passage Panels  
In  
cm  
Now Part of  
1950 Camino Vida Roble, Suite 150  
Carlsbad, CA 92008  
Tel: 760.438.7000 800.421.1587  
www.aigismech.com • www.linearcorp.com  
Copyright © 2011 Linear LLC  
231465 A  
 

Kyocera Cell Phone 82 K5243 User Manual
Land Pride Tiller RTR1042 User Manual
Leica Stud Sensor 760498a User Manual
Lenovo Computer Monitor LT2223ZWC User Manual
Life Fitness Stepper Machine LS 1000 User Manual
Life Fitness Treadmill 8860701 User Manual
Lincoln Electric Welding System IM526 B User Manual
Lucent Technologies Network Router merlin messaging system User Manual
Magic Chef Oven Electric Built In Double Cavity Wall Oven User Manual
Maytag Refrigerator MFI2067AEW User Manual