Magnavox VCR CMWV405 User Manual

RF Output Channel  
If channel 3 is already occupied for broadcasting,  
ꢀ) Set your TV to channel 4.  
2) Insert a pre-recorded tape into this unit.  
3) Press [PLAY B] once.  
4) After a few seconds, hold [PLAY B] on the unit for 3 seconds.  
• The RF output channel will change to channel 4 from channel 3  
and you will see a playback picture.  
If you need additional operating assist-  
ance after reading this owner’s manual  
or to order replacement accessories,  
please call  
Hint  
• The RF output channel  
does not change when  
you adjust tracking during  
playback. In this case, stop  
the playback, and start  
the playback again. After  
that, hold [PLAY B] on the  
VCR for 3 seconds again.  
Owner’s Manual  
TOLL FREE : 1-800-605-8610  
Video Cassette Recorder  
CMWV405  
When a picture does not appear on the TV screen, repeat step 4.  
5) Press [STOP C] to stop playback.  
1. Before Using Your VCR  
Stereo TV Connection  
VIDEO  
IN  
AUDIO  
IN  
You can use the AUDIO OUT jack and  
VIDEO OUT jack on the back of the  
VCR if your TV has Audio/Video Input  
jacks. In this case, you need to set the  
TV to external Line Input Mode. Please  
refer to your TV’s owner’s manual.  
ANT  
Basic TV Connection  
IN  
AUDIO  
OUT  
IN  
OUT  
Antenna  
Antenna  
Cable TV  
Signal  
or  
Cable TV  
Signal  
or  
(Back of VCR)  
VIDEO  
Audio/Video Cables  
(not supplied)  
ANT  
IN  
(Back of TV)  
(Back of TV)  
OUT  
VIDEO  
IN  
AUDIO  
IN  
ANT  
IN  
2
(Back of VCR)  
(Back of TV)  
Disconnect  
3
OUT  
Connect  
Front & Rear Terminals  
Connect  
AUDIO OUT jack  
AUDIO IN jack  
RF Cable (supplied)  
RF Cable  
(not supplied)  
RF Cable  
(not supplied)  
Connect the audio cable here through to the audio  
input jack of a camcorder, another VCR, a stereo  
amplifier or an audio system.  
Connect the audio cable coming from the  
audio output jack of a camcorder, another  
VCR or an audio source here.  
Plug the AC power cords of the VCR and TV into the AC outlets.  
4
ANT  
ANT IN jack  
Connect your antenna or cable box here.  
IN  
ANT  
IN  
AUDIO  
AUDIO  
OUT  
IN  
OUT  
Hint for Cable Box or Satellite Box  
ANT OUT jack  
OUT  
IN  
VIDEO  
OUT  
Connect the supplied RF cable to the  
VIDEO  
antenna input jack on your TV.  
(Back of VCR)  
(Cable box or  
VIDEO OUT jack  
ANT  
Antenna or  
Cable TV  
signal  
Satellite box)  
IN  
Connect the video cable here through the video  
input jack of a camcorder, another VCR or a TV.  
IN  
VIDEO IN jack  
O
U
T
E
OUT  
RF cable  
(supplied)  
Connect the video cable coming from the  
video output jack of a camcorder, another  
VCR or an audio-visual source (laser disc  
player, video disc player, etc.) here.  
RF Cables  
(not supplied)  
(Back of TV)  
STANDBY-ON  
CHANNEL  
MENU RECORD  
VIDEO  
AUDIO  
IR  
POWER  
VCR/TV  
CST.IN  
TIMER  
RECORD  
Select this connection when you want to view  
or record a scrambled channel. With this con-  
nection, channels cannot be changed on the  
unit. You can view or record ONLY the chan-  
nels you have selected on the cable box or  
the satellite box.  
(the same channel as the output channel of  
the cable box or satellite box).  
• If you use the channel 4, you need to  
change the unit’s RF output to channel 4.  
Refer to “RF Output Channel”.  
2) At the TV, select channel 3 or 4 (the same  
channel as you have selected at step ꢀ).  
3) On the cable box or satellite box, select the  
channel you want to view or record.  
• To use the input jacks on the back of this unit, press [0], [0], [1] on the remote control.  
• To use the input jacks on the front of this unit, press [0], [0], [2] on the remote control.  
Installing the Batteries for  
the Remote Control  
Supplied Accessory  
• Remote control  
(NA374UD) with  
two AA batteries  
• RF cable  
• Owner’s manual  
While you are recording, only the recorded  
channel can be viewed.  
Install two AA batteries  
(supplied) matching  
the polarity indicated  
on the bottom of the  
remote control.  
(WPZ090ꢀTM002) (ꢀVMN22462)  
Printed in China  
ꢀVMN22462 / HJ34RCD ★★★★★  
- ꢀ -  
EN  
 
3. Preparation for Use  
Turn on the Unit for the First Time  
To Add/Delete Channels  
Clock Set Up  
To Select a Channel  
MENU  
- M E N U -  
- M E N U -  
1
Turn on the TV and set it  
to channel 3.  
MENU  
1
1
5
6
7
CLOCK SET  
You can select a channel by using  
the Number buttons on the  
remote control.  
Notes for using the Number buttons:  
• When selecting cable channels  
which are higher than 99, enter  
channel numbers as a three-digit  
number (for example: ꢀꢀ7, press  
[1], [1], [7]).  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
B CHANNEL SET UP  
CLOCK SET  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
B CLOCK SET  
MONTH DAY  
YEAR  
ꢀ 0 0 2 MON 2 0 0 6  
/
If channel 3 is already occupied  
for broadcasting, see “RF Output  
Channel” section on page ꢀ.  
HOUR MINUTE AM/PM  
0 5 – – – –  
LANGUAGE SELECT  
LANGUAGE SELECT  
or  
:
or  
Select the current hour.  
• If the clock is not set,  
the CLOCK SET screen  
appears when you press  
[MENU]. In this case, go  
to step 2.  
or  
Remote Control TV Screen  
STANDBY-ON  
2
LANGUAGE SELECT  
• You must precede single-digit  
channel numbers with a zero (for  
example: 02, 03, 04 and so on).  
CLOCK SET  
B ENGLISH  
FRANCAIS  
ESPAÑOL  
[ON]  
MONTH DAY  
YEAR  
ꢀ 0 0 2 MON 2 0 0 6  
/
2
3
CHANNEL SET UP  
To Preset the Channel Again  
HOUR MINUTE AM/PM  
0 5 4 0 – –  
or  
2
3
4
CLOCK SET  
or  
AUTO SET UP  
:
MONTH DAY  
ꢀ 0 – –  
YEAR  
ꢀ) Press [MENU] until the main  
menu appears.  
B MANUAL SET UP  
/
– – – –  
or  
HOUR MINUTE AM/PM  
– – – – – –  
Select the current minute.  
CLOCK SET  
2) Select "CHANNEL SET UP" by  
pressing [PLAY B] or [STOP C].  
Then, press [F.FWD g].  
3) Select "AUTO SET UP" by  
pressing [PLAY B] or [STOP C].  
Then, press [F.FWD g]. After  
scanning, the tuner stops on the  
lowest memorized channel.  
or  
:
Select the current month.  
3
CH 0ꢀ  
AUTO SET UP  
MONTH DAY  
YEAR  
ꢀ 0 0 2 MON 2 0 0 6  
/
MANUAL SET UP  
HOUR MINUTE AM/PM  
CHANNEL 30 (CATV)  
ADD  
CLOCK SET  
or  
0 5  
:
4 0  
P M AM  
B PM  
MONTH DAY  
ꢀ 0 0 2  
YEAR  
– – – –  
To Change the On-Screen  
Language  
/
or  
Do you connect the cable from the cable box  
or the satellite box to the VCR’s ANT-IN jack?  
HOUR MINUTE AM/PM  
– – – – – –  
Select “AM” or “PM”.  
or  
:
ꢀ) Press [MENU] until the main  
menu appears.  
Yes  
Select the channel to be  
added or deleted.  
Yes Press [MENU]  
to exit.  
Select the current day.  
2) Select "LANGUAGE SELECT" by  
pressing [PLAY B] or [STOP C].  
Then, press [F.FWD g].  
3) Select "ENGLISH", "FRANCAIS"  
or "ESPAÑOL" by pressing  
[PLAY B] or [STOP C]. Then,  
press [C.RESET/EXIT].  
• Refer to “Hint for Cable Box or  
8
To exit the  
No  
Satellite Box” section on page ꢀ.  
CLOCK SET screen  
4
5
MANUAL SET UP  
No Please wait for a few minutes.  
CLOCK SET  
CHANNEL 30 (CATV)  
DELETE  
After scanning...  
MONTH DAY  
ꢀ 0 0 2  
YEAR  
2 0 0 6  
/
• The tuner stops on the lowest memorized  
channel.  
or  
HOUR MINUTE AM/PM  
– – – – – –  
or  
You can select only the channels memorized  
in the unit by using [CHANNEL ].  
:
Hint  
Hint  
Select “ADD” or “DELETE”.  
If you accidentally select Spanish  
or French and need English: Press  
[MENU] and choose SELEC. IDIOMA,  
or SELECTION LANGUE. Press  
[F.FWD g] and select ENGLISH.  
Finally, press [C.RESET/EXIT].  
• If "AUTO SET UP" appears on the TV  
• To go back one step, press [REW h]  
screen again, check the cable connections.  
(during steps 2 to 7).  
Select the current year.  
Then, press [F.FWD g] once again.  
• Your clock setting will be lost if either there  
is a power failure or if this unit has been  
unplugged for more than 30 seconds.  
Hint  
C.RESET  
EXIT  
To exit the  
menu  
Repeat these steps only if either there  
was a power failure or if this unit has been  
unplugged for more than 30 seconds.  
- 3 -  
EN  
 
4. Precautions  
Precautions  
Troubleshooting guide  
Install Location  
For safety and optimum performance of  
this unit:  
Important Copyright Information  
If this unit does not perform properly when operated as instructed in this Owner’s  
Manual, check this unit consulting the following checklist.  
Unauthorized recording or use of broad-  
cast television programming, video tape,  
film or other copyrighted material may  
violate applicable copyright laws. We  
assume no responsibility for the unau-  
thorized duplication, use, or other acts  
which infringe upon the rights of copy-  
right owners.  
PROBLEM  
CORRECTIVE ACTION  
• Install the unit in a horizontal and  
stable position. Do not place anything  
directly on top of the unit. Do not place  
the unit directly on top of the TV.  
• Shield it from direct sunlight and keep  
it away from sources of intense heat.  
Avoid dusty or humid places. Avoid  
places with insufficient ventilation for  
proper heat dissipation. Do not block  
the ventilation holes on the sides of the  
unit. Avoid locations subject to strong  
vibration or strong magnetic fields.  
No power.  
• Make sure the power plug is connected to an AC outlet.  
• Make sure the power is turned on.  
Timer recording is impossible.  
• Make sure the timer recording is set correctly.  
• Make sure the power is off.  
• Make sure the VCR clock is set correctly.  
Cannot go into Recording mode. • Make sure the tape has a record tab. If needed, cover the hole with  
adhesive tape.  
A Note about Recycling  
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing  
[CHANNEL  
].  
This product's packaging materials are  
recyclable and can be reused. Please  
dispose of any materials in accordance  
with your local recycling regulations.  
Batteries should never be thrown away  
or incinerated but disposed of in accord-  
ance with your local regulations concern-  
ing chemical wastes.  
Cannot view a tape but the audio  
is OK.  
Head cleaning may be necessary. Refer to “Auto Head Cleaning” on  
page 8.  
• Make sure the VCR is not in the Menu mode.  
No or poor playback picture.  
• Change the RF output channel to CH4. Then select the same  
channel on the TV.  
Avoid the Hazards of Electrical Shock  
and Fire  
• Do not handle the power cord with wet  
hands.  
• Do not pull on the power cord when  
disconnecting it from AC wall outlet.  
Grasp it by the plug.  
• Fine tune your TV.  
TV programs cannot be seen  
normally.  
• Re-check the ANT-IN and ANT-OUT connections. See page ꢀ.  
• Press [VCR/TV] on the remote control so that the VCR/TV indicator  
on the unit disappears.  
No operation from the infrared  
Remote Control.  
• Make sure the power plug is connected to an AC outlet.  
• Check batteries in remote control.  
Note to the Cable TV System Installer  
This reminder is provided to call the  
Cable TV system installer’s attention to  
Article 820-40 of the NEC that provides  
guidelines for proper grounding and  
in particular, specifies that the cable  
ground should be connected to the  
grounding system of the building, as  
close to the point of cable entry as pos-  
sible.  
Video or color fades in and out when • You cannot copy a copyrighted video tape. You are experiencing  
making a copy of a video tape.  
copy guard protection.  
Moisture Condensation Warning  
Specifications  
Moisture condensation may occur inside  
the unit when it is moved from a cold  
place to a warm place, or after heating  
a cold room or under conditions of high  
humidity. Do not use the unit at least for  
2 hours until its inside is dry.  
Video Heads :  
Operating temperature : 4ꢀ°F~ꢀ04°F  
(5°C~40°C)  
Four Heads  
Power requirement : ꢀ20V, 60Hz  
Power consumption : ꢀ4 Watts  
Dimensions :  
W ꢀ4-3/ꢀ6" (360mm)  
Converter output :  
VHF Channel 3 or 4  
H 3-5/8" (92mm)  
D 8-9/ꢀ6" (2ꢀ6mm)  
4.0 lbs. (ꢀ.8 Kg.)  
(approx.)  
Weight :  
CAUTION:  
FCC Warning  
TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUg TO  
WIDE SLOT, FULLY INSERT.  
• Designs and specifications are subject to change without notice and legal obligation.  
• If there is a discrepancy between languages, the default language will be English.  
This equipment may generate or use  
radio frequency energy. Changes or  
modifications to this equipment may  
cause harmful interference unless the  
modifications are expressly approved in  
the instruction manual. The user could  
lose the authority to operate this equip-  
ment if an unauthorized change or modi-  
fication is made.  
Make your contribution to the environment!!!  
• Used up batteries do not belong in the dust bin.  
• You can dispose of them at a collection point for used up batteries or  
special waste. Contact your council for details.  
- 4 -  
EN  
 
5. Playback  
Turn on the TV and set it to  
channel 3.  
7. Other Operations  
To cue or review picture during  
playback (Picture Search)  
To play back in slow motion  
Before:  
STANDBY-ON  
CHANNEL  
Press [SLOW] during playback or the still mode.  
• If the noise bar appears on the TV  
screen, you can reduce it by pressing  
VCR/TV  
3
EJECT  
1
Press [F.FWD g] or [REW h].  
• Press it again and the VCR will now  
search in super high speed (in the LP/  
SLP modes only).  
4
3
• If channel 3 is already occupied for broad-  
casting, see “RF Output Channel” section.  
2
[CHANNEL  
].  
4
5
8
6
PLAY  
REW  
F.FWD  
STOP/EJECT  
SEARCH  
-MODE  
CHANNEL  
MENU RECORD  
7
9
To temporarily stop recording  
2
1
IR  
Remote Control TV Screen  
POWER  
VCR/TV  
CST.IN  
TIMER  
RECORD  
C.RESET  
EXIT  
To freeze the picture on TV screen (Pause mode)  
during playback (Still mode)  
MENU  
0
SLOW  
PAUSE  
/STILL  
RECORD  
SPEED  
DISPLAY  
Press [PAUSE/STILL].  
PLAY  
B
• During the rec pause mode, five  
C
Press [PAUSE/STILL]. Each time you  
press the button, the picture will be for-  
warded by one frame.  
• If the picture begins to vibrate vertically  
during the still mode, stabilize the pic-  
3
4
marks appear on the TV screen. Each  
mark represents one minute.  
C
POWER  
VCR/TV  
CST.IN  
2
1
2
• Press it again to resume recording.  
Hint  
3
4
Auto Rewind  
When a tape reaches its end during play-  
back, fast-forward, or recording (except  
timer recording and One Touch Recording),  
the tape will automatically rewind to the  
beginning. After rewinding finishes, the unit  
will eject the tape and turn itself to off.  
ture by pressing [CHANNEL  
].  
EJECT  
• When a tape without record tab is inserted, the unit will start playback  
automatically at step ꢀ.  
• Tracking will be automatically adjusted upon playback. To adjust the  
tracking manually, press [CHANNEL  
• If the picture is distorted or rolling verti-  
cally, adjust the vertical hold control on  
your TV if equipped.  
STOP  
EJECT  
A
].  
Counter Reset  
Press [C.RESET/EXIT].  
Hint  
6. Recording & OTR (One Touch Recording)  
Before:  
• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to  
the tape and the video head.  
Turn on the TV and set it to  
channel 3.  
2
• To return to playback from the Picture Search/Still/Slow mode, press [PLAY B].  
If channel 3 is already occupied for broad-  
casting, see “RF Output Channel” section.  
STANDBY-ON  
VCR/TV  
3
EJECT  
1
8. On-Screen Operations  
6
Remote Control TV Screen  
1
2
1
4
7
2
with tab  
CHANNEL  
4
5
8
6
1
2
3
4
To call up the main menu  
2
5
8
0
3
6
9
PLAY  
SEARCH  
-MODE  
REW  
F.FWD  
CHANNEL  
STOP/EJECT  
CHANNEL  
MENU RECORD  
7
9
CHꢀ2  
MENU  
- M E N U -  
IR  
C.RESET  
EXIT  
POWER  
VCR/TV  
CST.IN  
TIMER  
RECORD  
MENU  
0
SLOW  
B TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
POWER  
VCR/TV  
CST.IN  
Select the chan-  
nel to record.  
PAUSE  
/STILL  
PLAY  
REW  
F.FWD  
RECORD  
STOP/EJECT  
SPEED  
DISPLAY  
MENU RECORD  
4
3
5
IR  
POWER  
VCR/TV  
CST.IN  
TIMER  
RECORD  
LANGUAGE SELECT  
Select the desired tape  
speed.  
3
SP  
SPEED  
5
6
To select an item  
Tape Speed  
Recording/Playback Time  
1
2
Type of tape  
SP mode  
SLP mode  
T60  
T120  
2hours  
6hour  
T160  
2-2/3hours  
8hour  
4
- M E N U -  
1
4
2 3  
1hour  
3hour  
or  
TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
B CHANNEL SET UP  
CLOCK SET  
RECORD  
4
Accidental erasure prevention  
To prevent accidental recording on a  
recorded cassette, remove its record tab.  
To record on it later, cover the hole with  
adhesive tape.  
LANGUAGE SELECT  
STANDBY-ON  
RECORD  
REC  
VCR/TV  
3
EJECT  
1
To decide  
2
Press [RECORD] repeatedly to select the  
desired recording length.  
CHANNEL  
Record tab  
CHANNEL SET UP  
4
5
8
6
SEARCH  
-MODE  
REC  
OTR(0:30)  
OTR(ꢀ:00).....  
7
9
AUTO SET UP  
(Normal recording)  
C.RESET  
EXIT  
B MANUAL SET UP  
MENU  
0
SLOW  
OTR(8:00)  
OTR(7:30)  
4 1  
2
4
3
PAUSE  
/STILL  
RECORD  
SPEED  
DISPLAY  
EJECT  
5
6
Hint  
To exit the menu  
STOP  
EJECT  
A
C.RESET  
EXIT  
MENU  
• If you have connected this unit to a cable box or satellite box, refer to  
“Hint for Cable Box or Satellite Box” section on page ꢀ.  
or  
- 5 -  
EN  
 
9. Recording Features  
Timer Recording  
Hints for Timer Recording  
•Insert a tape with its record tab into the unit.  
• If there is a power failure or the unit has been unplugged for more than 30 sec-  
onds, the clock setting and all timer settings will be lost.  
• If the tape runs out before the end time, the unit will switch to the Stop mode  
immediately, eject the tape and the power will be turned off. The TIMER indicator  
will flash.  
- M E N U -  
ONE TIME PROGRAM  
PROGRAM NUMBER  
1
5
Select the desired start  
time (hour).  
9
B TIMER PROGRAMMING  
AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
MENU  
DATE  
ꢀ 0 / 2 3 MON  
START TIME 0 7 : 3 0 PM  
END TIME 0 8 : 3 0 PM  
ONE TIME PROGRAM  
or  
• If a tape is not in the unit or does not have the record tab, the TIMER indicator  
flashes and timer recording cannot be performed. Please insert a recordable tape.  
When all the Timer Recording are completed, the TIMER indicator flashes.  
To play or eject the recorded tape, press [STANDBY-ON] first, and then  
PROGRAM NUMBER  
DATE ꢀ 0 / 2 3 MON  
START TIME 0 7 : 3 0 – –  
END TIME – – : – – – –  
LANGUAGE SELECT  
or  
CHANNEL  
ꢀ 6  
REC SPEED SP  
B SP  
SLP  
CHANNEL  
– –  
Select the desired recording speed.  
REC SPEED – –  
press [PLAY  
B] or [EJECT  
A].  
C.RESET  
EXIT  
Select the  
minute.  
To cancel a Timer Recording that is in progress  
Press [STOP/EJECT ] on the unit.  
P
N
2
PROGRAM NUMBER  
DATE – – / – –  
or  
STANDBY-ON  
10  
Turn off the  
VCR for  
recording.  
Copying a Video Tape  
START TIME – – : – – – –  
END TIME – – : – – – –  
CHANNEL  
REC SPEED – –  
– –  
Warning: Unauthorized recordings of copyrighted video tapes  
or  
may be an infringement of copyright laws.  
(Back of TV)  
TIMER indicator on the VCR lights up.  
Select an empty program  
number.  
(Back of Playing VCR)  
(Back of Recording VCR*)  
Hint  
ONE TIME PROGRAM  
PROGRAM NUMBER  
6
• To go back one step, press  
[REW h] (during steps 3 to 9).  
ANT  
IN  
2
AUDIO  
OUIN  
VIDEO  
DATE  
ꢀ 0 / 2 3 MON  
OUT  
OUT  
1
Connect  
START TIME 0 7 : 3 0 PM  
END TIME – – : – – – –  
OUT  
IN  
IN  
Connect  
or  
To Check, Correct, or Cancel  
a Timer Program  
VIDEO  
AUDIO  
CHANNEL  
REC SPEED – –  
– –  
3
4
PROGRAM NUMBER  
AM  
RF Cable  
(supplied)  
B ONCE  
DAILY  
WEEKLY  
B PM  
ꢀ) Turn the power on by pressing  
[STANDBY-ON].  
Audio/Video Cables  
(not supplied)  
Select “AM” or “PM”.  
*Front input jacks are also available  
or  
ꢀ) Insert a pre-recorded tape into the playing VCR.  
2) Insert a tape with its record tab into the recording VCR.  
2) Select main menu by pressing  
[MENU].  
Select “ONCE”, “DAILY”  
(Mon-Fri), or “WEEKLY”.  
3) Select "TIMER PROGRAMMING" by  
3) Press [SPEED] on the remote control of the recording VCR to select  
7
8
Repeat the procedure in steps  
5 and 6 to set the end time.  
pressing [PLAY B] or [STOP C]  
.
the desired recording speed (SP/SLP).  
Then, press [F.FWD g]  
.
4) Select the “Lꢀ” or “L2” position on the recording VCR.  
4) Select the program number  
which you want to check by  
pressing [PLAY B] or  
• To use the input jacks on the back of this unit, select "Lꢀ" position by  
Select the desired month.  
pressing [0], [0], [1] on the remote control or [CHANNEL  
].  
ONE TIME PROGRAM  
[STOP C]. The details of the  
program you selected will  
appear on the TV screen.  
• Go to the digit you want to  
change by pressing  
[F.FWD g] or [REW h].  
Then, enter correct numbers by  
pressing [PLAY B] or  
PROGRAM NUMBER  
DATE ꢀ 0 / 0 2 MON  
START TIME – – : – – – –  
END TIME – – : – – – –  
ONE TIME PROGRAM  
• To use the input jacks on the front of this unit, select "L2" position by  
or  
PROGRAM NUMBER  
DATE ꢀ 0 / 2 3 MON  
START TIME 0 7 : 3 0  
END TIME 0 8 : 3 0  
pressing [0], [0], [2] on the remote control or [CHANNEL  
5) Press [RECORD] on the recording VCR.  
].  
PM  
PM  
CHANNEL  
REC SPEED – –  
– –  
or  
6) Begin playback of the tape in the playing VCR.  
CHANNEL  
ꢀ 6  
REC SPEED – –  
7) To stop recording, press [STOP/EJECT  
P
N] on the recording VCR,  
then stop playback of the tape in the playing VCR.  
Select the desired day.  
Select the desired channel.  
If you have connected the unit to a cable  
box or satellite box as the Connection on  
page ꢀ, select the VCR to channel 3 or 4  
(the RF output channel of the VCR). Then,  
select the desired channel at the cable  
box or satellite box. Leave the cable box  
or satellite box on for timer recording.  
Hint  
[STOP C].  
• You can program one  
year in advance.  
or  
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The  
remote control might affect the playing VCR’s operation.  
You may cancel the entire  
program by pressing [REW h]  
while the program number flashes.  
5) Press [C.RESET/EXIT] to exit.  
6) Press [STANDBY-ON] to return  
to timer stand-by mode.  
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are  
not recommended.  
You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs.  
• “Lꢀ” or “L2” is found before the lowest memorized channel. (Example: CH02)  
• "L2" input jacks are on the front of this unit.  
- 6 -  
EN  
 
10. Special Features  
Time Search  
Index Search  
Auto Repeat  
You can search backward and  
forward a specific length of  
time on a tape.  
This function will playback a  
tape repeatedly from the begin-  
ning when the tape reaches to  
the end.  
You can skip the program backward  
and forward by the Index Mark.  
• Insert a tape into this unit.  
• Insert a tape into this unit.  
1
INDEX SEARCH  
SEARCH  
-MODE  
• Insert a tape into this unit.  
1
– –  
TIME SEARCH  
SEARCH  
-MODE  
MENU  
– : – –  
- M E N U -  
1
TIMER PROGRAMMING  
B AUTO REPEAT [OFF]  
CHANNEL SET UP  
CLOCK SET  
Press once.  
LANGUAGE SELECT  
Press twice.  
or  
2
INDEX SEARCH  
2
Select the desired length  
of time for fast forwarding  
or rewinding.  
0 3  
or  
TIME SEARCH  
2 : 5 0  
- M E N U -  
2
0ꢀ ~ 20  
CURRENT PROGRAM  
Beginning  
of tape  
TIMER PROGRAMMING  
B AUTO REPEAT [ON]  
CHANNEL SET UP  
CLOCK SET  
End  
or  
of tape  
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5  
02 01 01 02 03  
INDEX MARK  
LANGUAGE SELECT  
0:0ꢀ~ 9:59  
(ꢀ minute~9 hours  
and 59 minutes)  
To rewind To fast forward  
3
4
3
AUTO REPEAT  
B
To rewind  
To fast forward  
After searching,  
3
4
Hint  
After searching,  
• To cancel Auto Repeat, follow steps ꢀ-2  
above. Then, press [F.FWD g] so that  
[OFF] appears beside AUTO REPEAT.  
Press [C.RESET/EXIT] to exit.  
PLAYB  
• If menu remains on the TV screen at step  
3), press [C.RESET/EXIT] to exit.  
Hint  
PLAYB  
• The unit records an index mark at the  
beginning of the recording when you make  
a recording. There should be time gap  
between index marks for the Index Search.  
Hints for Index Search & Time Search  
• These functions are not available during recording.  
• Press [STOP C] to stop the search.  
• If the end of the tape is reached during a Search, the VCR will cancel the search  
and rewind the tape.  
- 7 -  
EN  
 
11. Information  
Maintenance  
Servicing  
Auto Head Cleaning  
LIMITED WARRANTY  
If this unit become inoperative, do not try to  
correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug  
the power plug, and please call our help line  
mentioned on page ꢀ to locate an Authorized  
Service Center.  
• This unit automatically cleans video heads  
as you insert or remove a cassette, so you  
can see a clearer picture.  
FUNAI CORP. will repair this product, free of charge in CANADA in the event of defect in materials or workmanship as  
follows :  
• Playback picture may become blurred or  
interrupted while the TV program recep-  
tion is clear. Dirt accumulated on the video  
heads after long periods of use, or the usage  
of rental or worn tapes can cause this prob-  
lem. If a streaky or snowy picture appears  
during playback, the video heads in your  
VCR may need to be cleaned.  
ꢀ. Please visit your local Audio/Video store  
and purchase a good quality VHS Video  
Head Cleaner.  
2. If a Video Head Cleaner does not solve  
the problem, please call our help line men-  
tioned on page ꢀ to locate an Authorized  
Service Center.  
DURATION :  
PARTS :  
LABOR :  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year  
from the date of original retail purchase. Certain parts are excluded from this warranty.  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the  
date of original retail purchase.  
Cabinet Cleaning  
• Wipe the front panel and other exterior sur-  
faces of the VCR with a soft cloth immersed  
in lukewarm water and wrung dry.  
• Never use a solvent or alcohol. Do not spray  
insecticide liquid near the VCR. Such chemi-  
cals may cause damage and discoloration to  
the exposed surfaces.  
LIMITS AND EXCLUSIONS :  
ThIs wARRANTy Is exTeNDeD ONly TO The ORIgINAl ReTAIl PURChAseR. A PURChAse ReCeIPT OR OTheR  
PROOF OF ORIgINAl ReTAIl PURChAse wIll be ReqUIReD TOgeTheR wITh The PRODUCT TO ObTAIN seRv-  
ICe UNDeR ThIs wARRANTy.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by AN UNAUThORIZeD seRvICe CeNTeR. This limited warranty does not apply to any  
product not purchased and used in CANADA.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product  
not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this prod-  
uct or damage which results from fire, flood, lightning or other acts of god.  
NOTES:  
• Remember to read the instructions included  
with the video head cleaner before use.  
• Clean video heads only when problems  
occur.  
ThIs wARRANTy DOes NOT COveR PACKINg MATeRIAls, ANy ACCessORIes (exCePT ReMOTe CONTROl),  
ANy COsMeTIC PARTs, COMPleTe AsseMbly PARTs, DeMO OR FlOOR MODels.  
FUNAI CORP. AND ITs RePReseNTATIves OR AgeNTs shAll IN NO eveNT be lIAble FOR ANy geNeRAl,  
INDIReCT OR CONseqUeNTIAl DAMAges ARIsINg OUT OF OR OCCAsIONeD by The Use OF OR The INAbIlITy  
TO Use ThIs PRODUCT. ThIs wARRANTy Is MADe IN lIeU OF All OTheR wARRANTIes, exPRess OR  
IMPlIeD, AND OF All OTheR lIAbIlITIes ON The PART OF FUNAI, All OTheR wARRANTIes INClUDINg The  
wARRANTy OF MeRChANTAbIlITy AND FITNess FOR A PARTICUlAR PURPOse, ARe heReby DIsClAIMeD by  
FUNAI AND ITs RePReseNTATIves IN CANADA.  
All wARRANTy INsPeCTIONs AND RePAIRs MUsT be PeRFORMeD by AN AUThORIZeD seRvICe CeNTeR.  
ThIs wARRANTy Is ONly vAlID wheN The UNIT Is CARRIeD-IN TO AN AUThORIZeD seRvICe CeNTeR.  
The PRODUCT MUsT be ACCOMPANIeD by A COPy OF The ORIgINAl ReTAIl PURChAse ReCeIPT. IF NO  
PROOF OF PURChAse Is ATTACheD, The wARRANTy wIll NOT be hONOReD AND RePAIRs COsTs wIll be  
ChARgeD.  
ATTENTION :  
FUNAI CORP. ReseRves The RIghT TO MODIFy ANy DesIgN OF ThIs PRODUCT wIThOUT PRIOR  
NOTICe.  
To locate your nearest AUThORIZeD seRvICe CeNTeR or for general service inquiries, please contact us at :  
FUNAI CORPORATION  
Customer Service  
Tel: 1-800-605-8610  
ꢀ9900 Van Ness Avenue, Torrance, CA 9050ꢀ  
- 8 -  
EN  
 

Land Pride Lawn Mower DH3510 User Manual
Lennox Hearth Bluetooth Headset SP5050 User Manual
LG Electronics Cell Phone 505C User Manual
Lindy Switch 25032 User Manual
Makita Power Hammer HPR2410 User Manual
M Audio Microphone KX TG7200 User Manual
Maximatic Slow Cooker MST 800V User Manual
Maxtor Computer Drive E01A200 User Manual
Meade Weather Radio TE346W User Manual
Metra Electronics Automobile Accessories 95 7323 User Manual