Marshall electronic Microcassette Recorder R144 User Manual

Marshall Electronics, Inc.  
1910 East Maple Ave. El Segundo, CA 90245  
Phone: (310) 333-0606 Fax: (310) 333-0688  
R144 Ribbon Microphone  
ank you for purchasing the MXL R144 Ribbon microphone. MXL microphones are the result of world-class engineering and  
manufacturing capabilities. Our microphones are designed to provide you with outstanding performance and exceptional value.  
With proper care, this mic will provide many years of satisfaction. For best results, please take a few moments to review this literature.  
General Characteristics  
e MXL R144 Ribbon microphone uses an aluminum ribbon transducer which by nature is a bidirectional (figure-8) pickup pattern. A figure-8  
pattern will pick up sounds from the front and back sides of the microphone with equal sensitivity while maintaining a large amount of rejection  
90° off access.e front of the microphone is indicated by the MXL logo where the audio signal is “in-phasewhile the back side has an inverted  
phase. Ribbon mics typically have a lower output than condenser microphones and may require a preamplifier with a lot of gain. It is highly  
recommended to use a preamp with low noise, high gain, and an input impedance of 1500 ohms or greater. We strongly advise experimentation  
with placement and isolation requirements with the gain initially set low to avoid possible equipment (and hearing) damage.  
Shockmount  
e MXL shockmount can shift during shipment. Simply shift the nylon bands to center the microphone in the assembly. Be sure that the wire  
clamp does not rest on the chassis of the mount as this impairs mechanical isolation. Slide the mount all the way to the rim of the microphone  
for the most secure hold.  
Power Requirements  
IMPORTANT! is microphone does NOT require a power supply. Use of phantom power with this microphone is NOT recommended as it can  
severally damage the ribbon element and cause the microphone to be unusable.  
Care/Handling  
e ribbon element is very fragile. Although each unit has been thoroughly checked by MXL, it is important to check the microphone as soon as you  
receive it to insure that it was not damaged in shipping.To help prevent transducer failure, avoid large vibrations and severe shock such as dropping  
the microphone. Never expose the microphone to large bursts of air as it can stretch or tear the ribbon element. It is highly recommended to use  
a pop-filter when using this microphone. Dust and foreign material (especially metal shavings) can degrade the performance of a microphone so  
always store the unit in its case. Never intentionally or accidentally apply power to the microphone as it can permanently damage the ribbon element.  
Please note: Damage to the ribbon is not covered by the warranty, and there will be a charge for a replacement.  
Microphone Cables  
is microphone connects to a preamp via XLR cable (not included). Cable can have a profound effect on the sound of any microphone. Even the  
finest microphones will sound poor if the cable allows noise to enter or causes distortion and loss of information. We recommend using Mogami  
cable. For more information about MXL microphones, visit mxlmics.com  
Frequency Response  
R144 Specifications:  
Type: Ribbon Velocity Microphone  
Ribbon Element: 1.8-micron aluminum ribbon  
Ribbon Length: 47mm  
Frequency Range: 20Hz -17kHz  
Polar Pattern: Figure 8  
Sensitivity: -56 dB (0 dB=1V/Pa)  
Impedance: 250 ohms  
Rated Load Impedance: >1500 Ohms  
0
Max SPL for 0.1% THD: >130 dB @1 kHz  
Size: 47mm x 171mm/1.85 in. x 6.75 in.  
Weight: 400g/0.85 lbs  
Polar pattern  
270  
90  
Metal Finish: Purple and chrome  
180  
Warranty  
Marshall microphones are guaranteed against defects in material and workmanship for one year from date of purchase. e ribbon element is not covered by the normal  
warranty so please check the microphone immediately upon receipt. Should you encounter any problem with this unit, promptly contact the company you purchased it  
from within five days of purchase for assistance. Contact Marshall directly for a quote to repair a damaged ribbon.e original dated sales receipt will be necessary for  
any warranty claim. Do not send any unit directly to us without prior authorization from our service department! Warranty coverage is limited to repair or replacement  
(at our option) of the microphone and does not cover incidental damages due to use of this unit, nor damage caused by accidental misuse of this product.  
 

Land Pride Brush Cutter RCR26 User Manual
Liebert Network Card XDH User Manual
Lightolier Indoor Furnishings 1101HIE User Manual
Lincoln Electric Welder SVM187 A User Manual
Lincoln Electric Welder V305 T AC User Manual
Lochinvar Water Heater CF 401 751 User Manual
Marmitek Indoor Furnishings 20061012 User Manual
Maverick Ventures Thermometer CT 01 User Manual
Meade Telescope AT111EDT User Manual
Meyer Spreader 8720 User Manual