Metra Electronics Car Stereo System 99 8225G User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-8225G  
APPLICATIONS  
Toyota Venza  
2009-2010  
99-8225G  
KIT FEATURES  
• DIN Head Unit Provision With Pocket  
• ISO DIN Head Unit Provision With Pocket  
Painted to match factory dash - G=Gray  
KIT COMPONENTS  
• A) Single DIN Radio Housing • B) ISO Brackets • C) Trim Plate  
B
C
A
WIRING AND ANTENNA CONNECTIONS  
(Sold Separately)  
• 70-1761 - 1987-up Toyota harness  
• TYTO-01 - 2003-up Toyota JBL amp interface  
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set  
• Magnetized Universal Swivel Head Socket Adapter  
1-800-221-0932  
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION  
 
99-8225G DASH DISASSEMBLY  
Toyota Venza 2009-2010  
A
1
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
2
3
Unclip and remove the trim panel to  
the right of the shifter. (Figure A)  
Remove (1) Phillips screw from the  
bottom of the climate control then  
unclip and remove the climate  
control. (Figure B)  
4
5
Remove (4)10 MM bolts securing the  
radio. Note: You will need a univer-  
sal swivel head socket adapter to  
get to the bottom left bolt.  
(Figure C)  
B
Remove (4) Phillips screws securing  
the factory radio to the a/c vent  
panel. (Figure D)  
Continue to kit assembly.  
D
C
REAR VIEW - RADIO AND A/C VENT PANEL  
RADIO  
1
 
99-8225G KIT ASSEMBLY  
DIN HEAD UNIT PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Secure the Radio Housing into the  
factory a/c vent panel using the  
factory hardware. (Figure A)  
A
REAR VIEW - A/C VENT PANEL  
Locate the factory wiring harness in  
the dash. Metra recommends using  
the proper mating adapter from Metra  
or AXXESS. Re-connect the negative  
battery terminal and test the unit for  
proper operation.  
3
Slide the DIN cage into the Radio  
Housing and secure by bending the  
metal locking tabs down. (Figure B)  
B
4
5
6
Slide the aftermarket head unit into  
the cage and secure. (Figure C)  
Snap the factory vent panel/Radio  
Housing over dash cavity. (Figure D)  
Reassemble remaining radio and  
dash assemblies in reverse order of  
disassembly.  
D
C
2
 
99-8225G KIT ASSEMBLY  
ISO DIN HEAD UNIT PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
Secure the Radio Housing into the  
1
2
3
A
factory a/c vent panel using the  
factory hardware. (Figure A)  
REAR VIEW - A/C VENT PANEL  
Mount the ISO Brackets to the head  
unit with the screws supplied with  
the unit. (Figure B)  
Slide the head unit into the radio  
opening until the side clips engage.  
(Figure C)  
4
5
6
Snap the Trim Plate into the Radio  
Housing. (Figure C)  
Snap the factory vent panel/Radio  
Housing over dash cavity. (Figure D)  
B
Reassemble remaining radio and  
dash assemblies in reverse order of  
disassembly.  
D
C
3
 
99-8225G  
NOTES  
4
 
99-8225G  
NOTES  
5
 
99-8225G INSTRUCTIONS  
1-800-221-0932  
REV. 05/20/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-8225G  
 

Lennox International Inc Furnace GSR21Q User Manual
Lenoxx Electronics Furnace G71P User Manual
Lexmark Printer X782e XL User Manual
LG Electronics Cell Phone VX3100 User Manual
LG Electronics Washer WM2487HMA User Manual
Lochinvar Water Heater CUPAK 04 User Manual
LST Smoke Alarm 55100 908 User Manual
Manhattan Computer Products Digital Camera 460392 User Manual
Martin Audio Speaker C101C User Manual
MB QUART Speaker ALX2PS User Manual