HV-36P38SJE
HV-32P37SJE
HV-28P37SJE
COLOUR TELEVISION
INSTRUCTIONS
Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
• Operate only from the power source specified
(AC 220 – 240 V, 50 Hz) on the unit.
• Avoid damaging the AC plug and power cord.
• When you are not using this unit for a long
period of time, it is recommended that you
disconnect the power cord from the main
outlet.
• The main power button on the TV does not
fully isolate the TV from the mains supply. If
you are not going to use this TV for a long
period of time, be sure to disconnect the mains
plug from the mains outlet.
Avoid improper installation and never put the unit where good
ventilation is not possible.
When installing this TV, distance recommendations must be
maintained between the set and the wall, as well as inside a tightly
enclosed area or piece of furniture.
Adhere to the minimum distance guidelines shown for safe operation.
Failure to heed the following precautions may result in damage to the TV or
remote control.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.
Never use any cleaner or detergent on it.
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.
D.I.S.T. demonstration
To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration:
Press the yellow button, b button, p p buttons or any of the number buttons.
3
CONTENTS
Setting up your TV ...................................5
Connecting the aerial and video cassette
recorder (VCR)....................................... 5
Connecting and placing the woofer unit
(HV-36P38SJE only) .............................. 7
Connecting the power cord to the AC
outlet....................................................... 8
Putting the batteries into the remote
control..................................................... 8
Initial settings ............................................. 8
T-V LINK functions................................... 12
SOUND menu ......................................... 30
STEREO / I • II.........................................30
BASS........................................................ 30
TREBLE ................................................... 30
BALANCE ................................................ 30
HEADPHONE VOLUME .......................... 30
3D CINEMA SOUND................................ 30
FEATURES menu................................... 31
SLEEP TIMER .........................................31
CHILD LOCK............................................ 31
APPEARANCE.........................................32
BLUE BACK............................................. 32
TV buttons and functions......................13
Turn the main power on........................... 14
Turn the TV on from standby mode ......... 14
Choose a TV channel .............................. 14
Adjust the volume .................................... 14
SET UP menu ......................................... 33
AUTO PROGRAM.................................... 33
EDIT/MANUAL.........................................33
LANGUAGE ............................................. 38
PICTURE TILT.........................................38
DECODER (EXT-2).................................. 38
EXT SETTING.......................................... 39
Remote control buttons and
functions..............................................15
Turn the TV on or off from standby mode ... 15
Choose a TV channel and watch images
from external devices ........................... 16
Adjust the volume .................................... 17
Information function ................................. 17
ZOOM function......................................... 18
3D CINEMA SOUND function.................. 19
Return to TV channel instantly................. 19
Using the FREEZE function..................... 19
Using the MULTI-PICTURE function ....... 20
Operating a JVC brand VCR or DVD
Additional preparation .......................... 42
Connecting external equipment ............... 42
Troubleshooting .................................... 45
Specifications ........................................ 47
player.................................................... 21
Teletext function ....................................22
Basic operation ........................................ 22
Using the List Mode ................................. 22
Hold.......................................................... 23
Sub-page ................................................. 23
Reveal...................................................... 23
Size.......................................................... 23
Index........................................................ 23
Cancel...................................................... 24
Using the TV’s menu..............................25
Basic operation ........................................ 25
PICTURE menu.......................................26
PICTURE MODE ..................................... 26
CONTRAST ............................................. 26
BRIGHT ................................................... 26
SHARP..................................................... 26
COLOUR.................................................. 26
HUE ......................................................... 26
COLOUR TEMP....................................... 26
FEATURES.............................................. 27
4
Setting up your TV
Caution
• Turn off all the equipment including the TV before connecting anything.
Connecting the aerial and video cassette recorder (VCR)
• The connecting cables are not provided.
• For further details, refer to the manuals provided with the devices to be connected.
„ If you are connecting a VCR,
HV-36P38SJE
Back of the TV
Aerial
follow A → B → C in the diagram
opposite.
75-ohm
Coaxial
Cable
„ If you are not connecting a VCR,
follow 1.
EXT-
4
EXT-1
To use the T-V LINK functions, you must
have a T-V LINK compatible VCR
connected by a SCART cable C to the EXT-
2 terminal on the TV. For details about T-V
LINK functions, see “T-V LINK functions”
on page 12.
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
21-pin
75-ohm
Coaxial
Cable
SCART
Cable
• You can watch a video using the VCR
without doing C. For details, see your
VCR instruction manual.
To Aerial
Input
VCR
• To connect more equipment, please see
“Connecting external equipment” on
page 42.
• To connect additional audio equipment,
see “Connecting speakers/amplifier” on
page 44.
• If you connect a decoder to a T-V LINK
compatible VCR, set the DECODER
(EXT-2) function to ON. For details, see
“DECODER (EXT-2)” on page 38.
Otherwise, you will not be able to watch
scrambled channels.
To Aerial
Output
AV IN/OUT
Terminal
HV-32P37SJE/HV-28P37SJE
Aerial
75-ohm
Coaxial
Cable
Back of the TV
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
21-pin
SCART
Cable
75-ohm
Coaxial
Cable
To Aerial
Input
VCR
To Aerial
Output
AV IN/OUT
Terminal
5
Setting up your TV
„ Rear Panel
HV-36P38SJE
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
1 Aerial socket (page 5)
2 Woofer terminal (pages 7)
3 EXT-1 terminal (pages 5, 39, 42)
4 EXT-2 terminal (pages 5, 12, 39, 42)
5 EXT-3 terminal (pages 39, 42)
6 EXT-4 terminal (pages 39, 42)
7 AUDIO OUT terminal (page 44)
HV-32P37SJE/HV-28P37SJE
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
1 Aerial socket (page 5)
2 EXT-1 terminal (pages 5, 39, 42)
3 EXT-2 terminal (pages 5, 12, 39, 42)
4 EXT-3 terminal (pages 39, 42)
5 EXT-4 terminal (pages 39, 42)
6 AUDIO OUT terminal (page 44)
6
Setting up your TV
Place the woofer unit within the range
of the connection cable.
It is recommended that the woofer unit be
placed with the speaker facing forwards.
Connecting and placing the
woofer unit (HV-36P38SJE
only)
Connect the supplied woofer connector to the
woofer terminal on the back of the TV.
If the woofer unit is not connected, you will
not be able to enjoy the bass sound.
• Connect so that the lever is raised.
Lever
EXT- 4
T-1
X
Y
T-2
X
E
S
L
Pb
R
r
P
T-3
X
E
S
Pay attention to the following in order
to prevent unnatural colours from
appearing in the corner of the screen.
• Place the woofer unit at least 20 cm away
from either side of the TV.
L
T
U
O
IO
D
U
A
R
• When disconnecting the woofer
connector, do so while pushing the lever.
• Do not place the woofer unit on top of the
TV.
• When the TV is used on a TV stand or
table, do not place the woofer unit
underneath the TV.
„ Placing the woofer unit
As shown in the diagram, fix the
supplied stoppers to the four corners
of the side of the woofer unit that will
be used as the base.
The woofer unit can be used either standing
up or lying down.
There is no difference between the top and
bottom of the woofer unit irrespective of
whether it is being used standing up or lying
down.
7
Setting up your TV
Connecting the power cord to
the AC outlet
Initial settings
When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.
Caution
• Operate only from the power source specified
(AC 220 – 240 V, 50 Hz) on the unit.
Yellow button
Blue button
Putting the batteries into the
remote control
7 buttons
Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.
1 Press the main power button on the
TV
The power lamp lights red (for power on),
then green (for TV on) and the JVC logo
appears.
HV-36P38SJE
• Follow the warnings printed on the
batteries.
• Battery life is about six months to one
year, depending on how much you use the
remote control.
Power lamp
Main power
button
HV-32P37SJE/HV-28P37SJE
• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.
• If the remote control does not work
properly, replace the batteries.
Power lamp
Main power
button
• If the power lamp stays red and does
not change to green:
Your TV is in the standby mode. To
turn the TV on, set the VCR/TV/DVD
switch on the remote control to the TV
position and press the # button. (See
page 15.)
8
Setting up your TV
• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
use the “LANGUAGE” and “AUTO
PROGRAM” functions to make the
initial settings. For details, see “SET
UP menu” on page 33.
4 Press the 5 and 6 buttons to
choose the country where you are
• To receive SKY 1 you need a satellite
tuner. You must have the satellite tuner
set to SKY 1 before starting the AUTO
PROGRAM function which follows.
5 Press the blue button to start the
AUTO PROGRAM function
The AUTO PROGRAM menu appears
and received TV channels are
automatically stored in the programme
numbers (PR).
2 Press the a button
The LANGUAGE menu appears.
> LANGUAGE
>> AUTO PROGRAM
CH 28
14%
OK
D0002(E)-EN
OK
3 Press the 6 buttons to choose
ENGLISH. Then press the a
button
D0004-EN
• Perform the “ACI function” operation
(see page 10) when “ACI START/ACI
SKIP” is displayed.
• To cancel the AUTO PROGRAM
function:
The on-screen display will then be in
English.
The COUNTRY menu appears as a sub-
menu of the AUTO PROGRAM function.
There are two COUNTRY menus.
Pressing the yellow button changes the
COUNTRY menu as follows:
Press the b button.
After the TV channels have been
registered in the programme
numbers (PR), the EDIT menu
appears
> COUNTRY
> EDIT
START
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
OK
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
MORE
> COUNTRY
ID
MANUAL
OK
MOVE
INSERT DELETE
D0038-EK
• If you want to, you can now edit the
programme numbers (PR) using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 33.
• If you do not want to edit programme
numbers (PR), go to the next step.
START
OK
MORE
D0003-EN
9
Setting up your TV
• The AUTO PROGRAM function does not
set the programme number PR 0 (AV) for
your video cassette recorder. You will
need to set this using the MANUAL
function.
6 Press the a button to display the
T-V LINK menu
T-V LINK
DOWNLOAD TV
VCR
• In some areas you may get TV reception
from more than one transmitter, for
example different ITV regions. In this
case each TV channel could be set twice.
If this happens, the first set of channels
will have the stronger signal. If you want
to delete the second set of channels, you
will have to do it manually (see page 33).
OK
EXIT
D0005-EN
If you do not have a T-V LINK
compatible VCR connected:
Press the b button to exit the T-V LINK
menu.
The T-V LINK menu disappears.
If you have a T-V LINK compatible
VCR connected to the EXT-2
terminal:
Follow the operating procedure
“Downloading the data to VCR” on
page 11 to transmit the Programme
number (PR) data.
Now, the initial settings are complete,
and you can watch the TV
• When the COUNTRY setting is
UNITED KINGDOM:
„ ACI function
This TV has an ACI function which decodes
the ACI (Automatic Channel Installation)
data.
BBC1, BBC2, ITV, Channel 4 and
Channel 5 are automatically set to the
programme numbers PR1 to PR5. If the
TV doesn't receive one of these TV
channels, that programme number (PR)
will not be set. Programme number PR6 is
not normally set.
Using the ACI function allows all TV
channels transmitted from the cable TV
station to be properly registered quickly
according to the data from the cable TV
station.
If “ACI START/ACI SKIP” appears in
the AUTO PROGRAM menu:
You can use the ACI (Automatic Channel
Installation) function to decode the ACI data
and complete the registration of all the TV
channels in a short period of time.
• When the COUNTRY setting is
IRELAND:
If your TV can detect the TV channel
name from the TV channel broadcast
signal, the TV channel name is assigned
to the programme number (PR) to which
the TV channel has been set. However,
which TV channels are set to which
programme numbers (PR) will depend on
the area in which you live.
• If a TV channel you want to view is not
set to a programme number (PR), you can
set it using the MANUAL function. For
details, see “EDIT/MANUAL” on
page 33.
Press the 6 buttons to choose ACI
START. Then press the a button to
start the ACI function
Depending on your cable TV station, there
may be a broadcast selection menu set up by
the cable TV station.
Follow the menu instructions and use the
5 and 6 buttons to operate the menu.
After you have made the setting, press the
a button.
10
Setting up your TV
• If you have any questions about the items
in the Broadcast Selection menu or how to
operate the menu, please contact your
cable TV station.
• If you don’t want to use the ACI function,
press the 6 buttons to choose ACI
SKIP and then press a.
1 Turn on the VCR
2 Press the a button
The data transmission begins.
DOWNLOAD TV
VCR
TRANSFER. . . . .
D0037-EN
• When the cable TV broadcast reception is
poor, the ACI function will not work
properly.
The T-V LINK menu disappears once the
data transmission ends.
• If there is an error in the ACI data itself,
the TV channel cannot be registered
properly. If this happens, turn the ACI
function off (ACI SKIP) and use the
AUTO PROGRAM function.
Alternatively, use the EDIT/MANUAL
function to correct the Programme
number (PR) setting.
When the T-V LINK menu is
changed over to another menu:
The TV has finished its menu. This new
menu is operated from the VCR. See the
VCR instruction manual for what to do
next.
If “FEATURE NOT AVAILABLE”
appears at the T-V LINK menu:
Check the following three items. Then
press the 2 button to retry data
transmission.
• Has a T-V LINK compatible VCR
been connected to the EXT-2
terminal?
• Has the VCR power been turned on?
• Does the SCART cable that is
connected to the EXT-2 terminal to T-
V LINK compatible VCR have all its
proper connections?
If “ACI ERROR” is displayed in the
AUTO PROGRAM menu:
“ACI ERROR” means that the ACI function
is not working properly. Press the 2 button
to start the ACI function again.
If “ACI ERROR” still appears even after you
have tried to start the ACI function several
times, press the 3 button to start the AUTO
PROGRAM function. It does not cause any
problem because all the TV channels are
registered to the Programme numbers (PR)
by the AUTO PROGRAM function.
„ Downloading the data to VCR
You can transmit to the latest Programme
numbers (PR) data to a VCR with the T-V
LINK function.
Caution
• This only works when a T-V LINK
compatible VCR is connected to the
EXT-2 terminal.
• This only works when the T-V LINK
menu is being displayed.
T-V LINK
DOWNLOAD TV
VCR
OK
EXIT
D0005-EN
11
Setting up your TV
„ Direct Rec
T-V LINK functions
“What You See Is What You Record”
When you have a T-V LINK compatible
VCR connected to the EXT-2 Terminal on
the TV, it is easier to set up the VCR and to
view videos. T-V LINK uses the following
features:
You can easily record to VCR the images
that you are watching on the TV.
For details, read the manual for your VCR.
Use your VCR controls. “VCR IS
RECORDING” is displayed.
To use T-V LINK functions:
A “T-V LINK compatible VCR” means a
JVC video cassette recorder with the T-V
LINK logo, or with one of the following
logos. However, these VCRs may support
some or all of the features described earlier.
For details, see your VCR instruction
manual.
In the following situations, the VCR
will stop recording if the TV is turned
off, if the TV channel or input is
changed, or if the menu is displayed
on the TV:
• when recording images from an external
device connected to the TV (for example
a camcorder)
• when recording a TV channel after it has
been unscrambled on a decoder
• when recording a TV channel by using the
TV’s output because the VCR’s own
tuner cannot properly receive that
channel.
“Q-LINK” (a trademark of Panasonic
Corporation)
“Data Logic” (a trademark of Metz
Corporation)
“Easy Link” (a trademark of Phillips
Corporation)
“Megalogic” (a trademark of Grundig
Corporation)
“SMARTLINK” (a trademark of Sony
When the VCR is not ready (for example
when there is no tape inserted), “NO
RECORDING” is displayed.
You cannot carry out Direct Rec using your
TV’s control.
Corporation).
„ Pre-set download
The VCR will automatically download the
registered data on the TV channels from the
TV. This means you do not need to set up the
program channels on your VCR manually.
The preset download function automatically
begins when the initial setting is complete or
whenever you carry out the AUTO
Generally, the VCR cannot record a TV
channel that it cannot receive properly on its
own tuner, even if you can view that TV
channel on the TV. However, some VCRs
can record a TV channel by using the TV’s
output if that channel can be viewed on the
TV. For details, see your VCR instruction
manual.
PROGRAM or EDIT/MANUAL functions.
You can also carry out this function using
your VCR controls.
When “FEATURE NOT AVAILABLE” is
displayed:
If “FEATURE NOT AVAILABLE” is
displayed, the download was not performed
correctly. Before trying to download again,
check that:
• the VCR power is turned on
• the VCR is T-V LINK compatible
• the VCR is connected to the EXT-2
terminal
• the SCART cable is fully wired.
12
TV buttons and functions
HV-36P38SJE
HV-32P37SJE/HV-28P37SJE
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT
-2
S
S
R
P
E
X
T
L
EXT-3
5
S
R
L
A
U
D
I
O
O
U
T
R
S
L
R
P
EXT-5
S
S
L
R
P
E
X
T
P
EXT-5
L
5
R
See the pages in parentheses for details.
See the pages in parentheses for details.
1 Remote control sensor
1 Remote control sensor
2 Power lamp (pages 8, 14)
2 Power lamp (pages 8, 14)
3 Main power button (pages 8, 14)
4 Headphone jack (mini jack) (page 42)
5 P p buttons/ q buttons (page 14)
6 r (Volume) button (page 14)
7 EXT-5 terminal (pages 39, 42)
3 Main power button (pages 8, 14)
4 Headphone jack (mini jack) (page 42)
5 P p buttons/ q buttons (page 14)
6 r (Volume) button (page 14)
7 EXT-5 terminal (pages 39, 42)
13
TV buttons and functions
Turn the main power on
Press the main power button on the
TV.
The power lamp lights red and your TV is in
standby mode.
• If the power lamp lights green, the TV is
already on.
To turn the main power off:
Press the main power button again.
The power lamp goes off.
Caution
• The main power button on the TV does
not fully isolate the TV from the AC
supply. If you are not going to use the TV
for a long period, be sure to disconnect
the AC plug from the AC socket.
Turn the TV on from standby
mode
Press the P p buttons to turn the TV
on from standby mode
Choose a TV channel
Press the P p buttons to choose a
programme number (PR) or an EXT
terminal
Adjust the volume
1 Press the r (Volume) button
The volume level indicator appears.
2 Press the q buttons while the
volume level indicator is displayed
14
Remote control buttons and functions
1 Muting button
2 Number buttons
3 Information button
4 c button
5 3 sound button
6 b button
7 7 buttons
8 g (Text) button
9 p p buttons
1
2
=
~
0 VCR/DVD/Teletext control buttons
- p buttons
= # (Standby) button
~ VCR/TV/DVD switch
! G button
3
4
!
@
#
@ Colour button
# X (Multi) button
$ f/g (Freeze/Swap) button
% H button
^ a button
& b button
$
5
6
%
^
* r (Volume) q buttons
7
8
&
*
Turn the TV on or off from
standby mode
9
Press the # (standby) button to turn
the TV on or off.
When the TV is turned on, the power lamp
changes from red to green.
0
-
• The power can be turned on by pressing
the b button, p p buttons or Number
buttons.
To turn the TV on or off, set the VCR/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the VCR/TV/DVD switch on the remote
control is set to a position other than TV,
the TV will not be turned on or off even if
the # button is pressed.
15
Remote control buttons and functions
• This TV set has a function which can
automatically change over the input
according to a special signal output
from an external device. (The EXT-4
and EXT-5 terminals do not support
this function.)
• Since this TV is designed to make full
use of the resolution of the original
video source, the motion may appear
unnatural when the video source is
input with 625p progressive-scanning
component signals.
If this happens, change the output
setting of the connected device to 625i
interlace-scanning component signal
output. See the instructions that came
with the device for more information.
Choose a TV channel and
watch images from external
devices
• If the picture is tilted, correct it. See
“PICTURE TILT” on page 38.
„ Use the number buttons:
Enter the programme number (PR)
of the channel using the number
buttons.
Example:
• PR 6 → press 6
• PR 12 → press 1 and 2
„ Use the p p buttons:
Press the p p buttons to
choose the programme number
(PR) you want or an EXT terminal.
To return to a TV channel:
Press the b button, the 6 buttons or the
number buttons.
„ Use the AV button:
Press the AV button to choose an
EXT terminal.
To use the programme number PR 0
(AV):
When the TV and VCR are connected only
by the aerial cable, choosing the programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 33.
TV mode
EXT modes
Programme
numbers
PR 1 – PR 99
EXT-2
EXT-1
or
EXT-3
or
S3
E3
Pressing the G button changes the choice as
follows:
EXT-5
EXT-4
EXT modes
TV mode
or
EXT-2
EXT-1
Programme
PR 0
• You can choose a video input signal
from the S-VIDEO signal (Y/C signal)
and regular video signal (composite
signal). For details, see “S-IN (S-
VIDEO input)” on page 39.
• If you do not have a clear picture or no
colour appears, change the colour
system manually. See “COLOUR
SYSTEM” on page 28.
numbers
or
PR 1 – PR 99
EXT-3
or S3
E3
EXT-5
EXT-4
or
• The VCR sends its playback image along
the aerial cable as an RF (radio frequency)
signal.
• If you choose an EXT terminal with no
input signal, the EXT terminal number
becomes fixed on the screen.
• Also see your VCR instruction manual.
16
Remote control buttons and functions
Time display:
The current time of the teletext data is
displayed.
Adjust the volume
Press the r q buttons to adjust
the volume.
The volume indicator appears and the
volume changes as you press the r q
buttons.
If the TV has not received a TV channel that
has teletext programmes since it was turned
on, the time display is blank. To view the
current time, choose a TV channel that has
teletext programmes. The time will continue
to be displayed until the TV is turned off
even if you choose other TV channels.
• An incorrect current time is sometimes
displayed when watching videos.
„ Muting the sound
Press the (muting) button to
l
turn off the sound.
Pressing the (muting) button again
l
PR LIST:
restores the previous volume level.
The programme number (PR) and EXT
terminal list is displayed.
Information function
Pressing the a button after choosing the
programme number (PR) or EXT terminal
with the 7 buttons will display the
chosen programme or EXT terminal.
• For programme numbers (PR) for which
the CHILD LOCK function is set, the n
(CHILD LOCK) mark is displayed. For
details see “CHILD LOCK” on page 31.
You can see the channel number of the
programme you are watching, the current
time or the PR LIST.
From the PR LIST, you can choose a channel
or EXT terminal.
Press the
(Information) button to
h
display the information you want to
see.
Pressing the
(Information) button changes
h
the display as follows:
PR LIST
PR
ID
Channel number display
12 : 00
AV
01
02
03
04
05
06
07
08
09
BBC1
No indication
OK
-10
+10
D0011-EN
Channel number display:
The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the EXT
terminal number is displayed.
17
Remote control buttons and functions
16:9 ZOOM:
This zooms up the wide picture (16:9 aspect
ratio) to the full screen.
ZOOM function
You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.
AUTO:
16:9 ZOOM SUBTITLE:
This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.
When a WSS (Wide Screen Signalling)
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed according to the ZOOM mode set
with the 4:3 AUTO ASPECT function.
• For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 29.
FULL:
This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.
• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.
• When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.
„ Choose the ZOOM mode
REGULAR:
Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.
1 Press the c button to display
the ZOOM menu
ZOOM
AUTO
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL
PANORAMIC:
This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.
OK
D0009-EN
2 Press the 6 buttons to choose a
ZOOM mode. Then press the a
button
• The top and bottom of the picture are
slightly cut off.
The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.
• The ZOOM mode may be
automatically changed by the control
signal from an external device. When
you want to return to the previous
ZOOM mode, choose the ZOOM
mode again.
14:9 ZOOM:
This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.
18
Remote control buttons and functions
„ Adjusting the visible area of the
picture
3D CINEMA SOUND function
If subtitles or the top (or bottom) of the
picture are cut off, you can adjust the visible
area of the picture manually.
You can enjoy sounds with a wider
ambience.
• This function does not work for the sound
from headphones.
1 Press the c button
The ZOOM menu appears.
Press the 3 button and choose
“ON”, “MONO” or “OFF”.
2 Press the a button to display the
ZOOM mode indicator
ON:
Choose to add the 3D CINEMA SOUND
effect to stereo sound.
The indicator appears.
16 : 9 ZOOM
MONO:
D0010-EN
Choose to add the 3D CINEMA SOUND
effect to mono sound.
3 While it is displayed, press the 6
buttons to change the position of
the picture
OFF:
Choose to cancel the 3D CINEMA SOUND
effect.
• The 3D CINEMA SOUND effect can be
adjusted with the “3D CINEMA
SOUND” menu (see page 30).
• You cannot adjust the visible area in
REGULAR or FULL mode.
Return to TV channel instantly
You can return to a TV channel instantly.
Press the b button
The TV returns to the TV mode and a TV
channel appears.
Using the FREEZE function
You can view the current programme as a
still picture.
1 Press the f button
The still picture of the current picture will
appear.
current
programme
still picture
D0056-EN
19
Remote control buttons and functions
To cancel the FREEZE function:
Press the f button, the p p buttons or
the number buttons.
• When set to 2-pictures multi, you can
view a TV picture and a picture from
an external device. You can not view a
TV picture on more than one screen at
the same time.
• When 12-pictures multi is set, pictures
from external devices are not
displayed.
• The FREEZE function does not work
while a sub-picture is displayed.
• The still picture cannot be output from
the TV.
• The FREEZE function does not work
for pictures of 625p, 525p and 1125i
signals.
• When set to 2-pictures multi, the main-
picture can be changed by pressing the
p p buttons. The sub-picture screen
can be changed by pressing the p
buttons.
When set to 12-pictures multi and
there are more than 12 pictures, the
next or previous 12 screens can be
displayed by pressing the p buttons.
Using the MULTI-PICTURE
function
1 Press the X button
The MULTI-PICTURE menu appears.
1
2
12
Changing the sub-picture
Displaying the next or
previous 12 screens
D0101-EN
2 Press the 5 buttons to choose
the number of screens and then
press the a button
• When set to 2-pictures multi, press the
g (swap) button to switch the main-
picture and sub-picture.
Choose to return to one screen.
1
•
2-pictures multi function does not
work for a picture of 1125i signal.
D0102
• A picture of 625p or 525p signal
cannot be displayed as the sub-picture.
Pay attention to the following.
Choose to change to 2-pictures multi.
2
D0103
- When the EXT-4 picture is a picture
of 625p or 525p signal, you cannot
choose EXT-4 with the p buttons.
- When the EXT-4 picture signal is
changed to 625p, 525p or 1125i
Choose to change to 12-pictures multi.
12
D0104
2-pictures multi:
signal while the EXT-4 picture is
displayed as the sub-picture, the 2-
pictures multi function is cancelled.
Main-
picture
Sub-
picture
D0056-EN
12-pictures multi:
Still
pictures
Moving
picture
D0058-EN
20
Remote control buttons and functions
- The pictures cannot be swapped
when a picture of 625p or 525p
signal from EXT-4 is being
Operating a JVC brand VCR or
DVD player
displayed as the main picture.
These buttons will operate a JVC brand VCR
or DVD player. Pressing a button that looks
the same as the device’s original remote
control button has the same effect as the
original remote control.
• Do not press the g (swap) button
while you are recording the TV output
on the VCR. If you do, the TV output
signal will change.
• You cannot view a scrambled channel
in the sub-picture. If the g (swap)
button is pressed when viewing a
scrambled channel in the main-picture
using an external decoder, the channel
you have been viewing in the sub-
picture will appear in both the main-
picture and sub-picture.
• When set to 2-pictures multi and the
headphones are connected, the sound
for the main-picture is output from the
TV speakers and the sound from the
sub-picture is output from the
1 Set the VCR/TV/DVD Switch to the
VCR or DVD position
VCR:
When you are operating the VCR, set the
switch to the VCR position.
• You can turn the VCR on or off with
the # (standby) button.
DVD:
When you are operating the DVD player,
set the switch to the DVD position.
• You can turn the DVD player on or off
with the # (standby) button.
headphones.
- Adjust the volume of the sub-picture
sound from the headphones with
“HEADPHONE VOLUME” in the
“SOUND” menu (see page 30).
- The main-picture sound can not be
heard through the headphones.
• When set to 12-pictures multi, press
the 7 buttons to choose the
screen you want to view and the press
the a button to display that picture
on the whole screen.
• The BLUE BACK function does not
work when the MULTI-PICTURE
function is being used.
• The ZOOM function does not work
when the MULTI-PICTURE function
is being used.
2 Press the VCR/DVD Control Button
to control your VCR or DVD player
• If your device is not made by JVC,
these buttons will not work.
• Even if your device is made by JVC,
some of these buttons may not work,
depending on the device you are using.
• You can use the p buttons to choose
a TV channel the VCR will receive, or
choose the chapter the DVD player
plays back.
• Some models of DVD player use the
p buttons for both operating the fast
forward/backward functions and for
choosing the chapter. In this case, the
253 buttons do not work.
To return the multi-picture to one
screen:
Press the M button, press the 5
buttons to choose one screen, and then
press the a button.
You cannot turn the TV on or off when the
VCR/TV/DVD switch is set to the VCR or
DVD position.
When you turn the TV on or off, set the
VCR/TV/DVD switch to the TV position.
• Pressing the b button will also return
the display to one screen.
21
Teletext function
4 Choose a teletext page by pressing
the p p buttons, number buttons
or colour buttons
VCR/TV/
DVD
To return to the TV mode:
Press the b button or g (Text) button.
• If you have trouble receiving teletext
broadcasts, consult your local dealer or
the teletext station.
• The ZOOM function will not work in
the TV and text mode or Text mode.
• You cannot operate menus when
viewing a teletext programme.
• Language display depends on the
country which was set on the
COUNTRY menu. If characters on a
Teletext programme do not appear
properly, change the COUNTRY
setting to other country’s. To change
the COUNTRY setting, perform steps
1 and 2 of the “AUTO PROGRAM”
procedure on page 33 and then press
the a button.
Basic operation
You can view three types of teletext
broadcasts on the TV:
FLOF (Fastext), TOP and WST.
• TOP is not available when the
COUNTRY setting is UNITED
KINGDOM.
1 Choose a TV channel with a teletext
broadcast
2 Set the VCR/TV/DVD switch to the
TV position
Using the List Mode
You can store the numbers of your favourite
teletext pages in memory and call them up
quickly using the colour buttons.
3 Press g (Text) button to display
the teletext
„ To store the page numbers:
1 Press B button to go into the
List mode
Pressing g (Text) button changes the
mode as follows:
The page numbers you have stored are
displayed at the bottom of the screen.
2 Press a colour button to choose a
position. Then press the number
buttons to enter the page number
TV mode
TV and text mode
Text mode
22
Teletext function
3 Press and hold down the A (Store)
button
Reveal
Some teletext pages include hidden text
(such as answers to a quiz).
You can display the hidden text.
The four page numbers blink white to
show that they are stored in memory.
„ To call up a stored page:
Each time you press the E (Reveal)
button, text is hidden or revealed
1 Press the B button to enter the
List mode
2 Press a colour button having a
stored page
Size
To exit the List mode:
You can double the height of the teletext
display.
Press the B button again.
Hold
Press the F (Size) button
You can hold a teletext page on the screen for
as long as you want, even while several other
teletext pages are being received.
Press the C (Hold) button
Hold indication
Index
To cancel the Hold function:
Press C (Hold) button again.
You can return to the index page instantly.
Press the G (Index) button
Returns to page 100 or a previously specified
page.
Sub-page
Some teletext pages include sub-pages that
are automatically displayed.
1 Choose a teletext page that
includes sub-pages
Sub-page numbers that can be viewed are
automatically displayed at the top of the
screen.
2 Press the 5 buttons to choose a
sub-page number
23
Teletext function
Cancel
You can search for a teletext page while
watching TV.
1 Press the number button to enter a
page number, or press a colour
button
The TV searches for a teletext page.
2 Press H (Cancel) button
The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.
3 Press H (Cancel) button to return
to a teletext page when the page
number is on the screen
• The TV mode cannot be resumed by
pressing the H (Cancel) button. To
return to the TV mode press b.
24
Using the TV’s menu
This TV has a number of functions you can
operate using menus. To use all your TV’s
functions, you need to understand the basic
menu operating techniques fully.
Types of menu
PICTURE menu
Choose to set the screen
settings.
D0106
D0107
D0108
Buttons used to operate the menus
SOUND menu
Choose to set the sound settings.
FEATURES menu
Choose to set the sleep timer
and child lock settings.
SET UP menu
Choose to edit the channels or
set the display language
settings.
D0109
The menu guide area can be made to appear
and disappear for some menus.
While the menu is displayed, press the h
button to change between the guide area
being displayed and not displayed.
Basic operation
1 Press the H button to display
the menu bar
>> 4:3 AUTO ASPECT
PICTURE
PANORAMIC
REGULAR
14:9 ZOOM
D0105-EN
2 Press the 5 buttons to choose
the menu you want to use and then
press the a button
OK
D0017-EN
Guide area
PICTURE
D1105-EN
Chosen
menu
Chosen
menu name
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
3 Press the 6 buttons to choose
the item to be set, press the 5
buttons to set the item, and then
press the a button
D1017-EN
• The guide area for some menus will still
be displayed even if the h button is
pressed. This is not a fault.
If there are sub-menus, use the 7
buttons to operate them.
• Press the b button to return to
the previous menu.
• Press the b or H button to exit
from the menu.
25
PICTURE menu
PICTURE
COLOUR
STANDARD
PICTURE MODE
CONTRAST
BRIGHT
SHARP
COLOUR
You can adjust the picture colour.
2 :lighter
HUE
COLOUR TEMP.
FEATURES
3 : deeper
COOL
RESET
HUE
OK
D0014-EN
You can adjust the picture tint.
2 :reddish
3 : greenish
• While the PICTURE menu is displayed,
pressing the blue button will set the
CONTRAST, BRIGHT, SHARP,
COLOUR, HUE settings to their default
settings.
• You can change the HUE setting (picture
hue) when the colour system is NTSC
3.58, or NTSC 4.43.
COLOUR TEMP.
PICTURE MODE
You can select one of three COLOUR
TEMP. modes (three tones of white) to adjust
the white balance of the picture. Since white
is the colour which is used as a reference for
all the other colours, changing the COLOUR
TEMP. mode affects the appearance of all
the other colours on the screen.
You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.
BRIGHT:
Heightens contrast and sharpness.
COOL:
STANDARD:
A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.
Standardizes picture adjustment.
SOFT:
Softens contrast and sharpness.
NORMAL:
The normal white colour.
CONTRAST
WARM:
You can adjust the picture contrast.
2 :lower
3 : higher
A reddish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.
BRIGHT
You can adjust the picture brightness.
2 :darker
3 : brighter
SHARP
You can adjust the picture sharpness.
2 :softer
3 : sharper
26
PICTURE menu
• The MAX setting is not suitable for high-
quality pictures which contain very little
noise.
FEATURES
Choose FEATURES and press the a or 3
button to display the sub-menu.
„ Super DigiPure
The Super DigiPure function uses the latest
in digital technology to give you a natural-
looking picture. The Super DigiPure function
includes the following two functions.
> FEATURES
DIGITAL VNR
Super DigiPure
MOVIE THEATRE
Colour DigiPure
COLOUR SYSTEM
4:3 AUTO ASPECT
AUTO(LOW)
AUTO
AUTO
ON
DigiPure function:
This function helps to create a natural-
looking picture by eliminating unnecessary
edges from high-contrast and crisp images.
For images with low-contrast, edges are
added to produce a sharper, more detailed
picture.
You can choose from the three DigiPure
function settings of AUTO, MIN and MAX.
• If you set the DigiPure effect too high on
a low-quality picture that contains a lot of
noise, this may actually make the noise
worse. We recommend you use the
AUTO setting if you can.
OK
D1015-EN
„ DIGITAL VNR
The DIGITAL VNR function cuts down the
amount of ‘noise’ (‘snow’ or interference) in
the original picture.
You can choose from the three DIGITAL
VNR function settings of AUTO, MIN and
MAX.
AUTO(LOW)/AUTO(HIGH):
The TV will automatically adjust the level of
the DIGITAL VNR effect to match the
amount of noise in the picture, giving you the
best possible picture.
• If you set the DIGITAL VNR effect too
high it can make the picture less sharp. It is
recommended you use the AUTO(LOW)
setting if you can. If you set the DIGITAL
VNR function to AUTO(LOW) but still
notice some noise, change the setting from
AUTO(LOW) to AUTO(HIGH).
Picture motion compensation
function:
This function displays fast-moving pictures
(for example, the players or ball in a football
game) more smoothly and naturally on the
screen.
• The effect level of the picture motion
compensation function cannot be
changed. The effect level is the same no
matter which of the AUTO, MIN or MAX
settings is used.
MIN:
The level of the DIGITAL VNR effect is set
to the minimum. If you set the DIGITAL
VNR function to AUTO(LOW) but feel that
the sharpness of the original picture has not
been reproduced fully, change the setting
from AUTO(LOW) to MIN.
AUTO:
The TV will automatically adjust the level of
the DigiPure effect to match the amount of
noise in the picture, giving the best possible
picture.
• The MIN setting is not suitable for low-
quality pictures which contain a lot of
noise.
MAX:
The level of the DIGITAL VNR effect is set
to the maximum. If you set the DIGITAL
VNR function to AUTO(HIGH) but still
notice some noise, change the setting from
AUTO(HIGH) to MAX.
27
PICTURE menu
MIN:
OFF:
The level of DigiPure effect is set to the
minimum. When you set the Super DigiPure
function to AUTO and notice some noise,
change the setting from AUTO to MIN.
• The MIN setting is not suitable for high-
quality pictures which contain very little
noise.
Colour DigiPure doesn't work. This gives a
less clear picture than when this function is
turned on.
„ COLOUR SYSTEM
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
MAX:
The level of DigiPure effect is set to the
maximum. If you set the Super DigiPure
function to AUTO but feel that the original
picture quality has not been reproduced fully,
change the setting from AUTO to MAX.
• The MAX setting is not suitable for low-
quality pictures which contain a lot of
noise.
1 Choose COLOUR SYSTEM. Then
press the a or 3 button
The sub-menu of the COLOUR SYSTEM
function appears.
>> COLOUR SYSTEM
MAIN
SUB
PAL
AUTO
OFF:
The Super DigiPure function is turned off.
„ MOVIE THEATRE
OK
The MOVIE THEATRE function displays a
cinema film picture more smoothly and
naturally on the screen.
D0016-EN
2 Press the 5 buttons to choose
AUTO:
MAIN or SUB
The television automatically recognizes the
type of signal and turns the function on and
off.
MAIN:
You can change the colour system of the
main-picture.
SUB:
You can change the colour system of the
sub-picture.
• Choose MAIN when a sub-picture is
not displayed.
ON:
This function is turned on.
OFF:
This function is turned off.
• The motion may appear unnatural when
viewing images with the NTSC colour
system. When the MOVIE THEATRE
function is set to AUTO or ON, the
motion may appear unnatural when
viewing images with the NTSC colour
system.
3 Press the 6 buttons to choose
the appropriate colour system.
Then press the a button
PAL:
PAL system
SECAM:
SECAM system
NTSC 3.58:
NTSC 3.58 MHz system
„ Colour DigiPure
Makes the colour outline stand out and
increases the sharpness giving a clearer
picture.
NTSC 4.43:
NTSC 4.43 MHz system
ON:
Colour DigiPure works. Normally use with
this function turned on.
28
PICTURE menu
AUTO:
This function detects a colour system
from the input signal. You can only use
this when you are viewing a picture from
programme number PR 0 (AV), or an
EXT terminal.
• The AUTO function may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
function, choose another colour system
manually.
• When in the Programme numbers PR 0
(AV) to PR 99, you cannot choose NTSC
3.58 or NTSC 4.43.
SECAM cannot be chosen when the
COUNTRY setting is UNITED
KINGDOM.
• “COLOUR SYSTEM” cannot be chosen
when you are watching the EXT-4
picture.
„ 4:3 AUTO ASPECT
You can choose one of three ZOOM modes,
REGULAR, PANORAMIC or 14:9 ZOOM,
as the ZOOM mode for the normal picture
(4:3 aspect ratio).
1 Choose 4:3 AUTO ASPECT then
press the a button
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
OK
D0017-EN
2 Press the 6 buttons to choose a
ZOOM mode
29
SOUND menu
SOUND
BALANCE
STEREO/
BASS
TREBLE
BALANCE
HEADPHONE VOLUME
3D CINEMA SOUND
You can adjust the volume balance between
the left and right speaker.
2 :turn the left speaker’s volume level up.
3 : turn the right speaker’s volume level up.
OK
HEADPHONE VOLUME
D0019-EN
Adjust the volume of the sub-picture sound
which is heard through the headphones when
set to 2-pictures multi.
2 :Reduce volume
3 : Increase volume
• Functions in the “SOUND” menu other
than “HEADPHONE VOLUME” work
for the TV speakers. They do not work for
the sound from the headphones.
• When the headphones are connected and
only one screen is displayed, only
• When not set to 2-pictures multi, the
headphone volume is adjusted with the
r q (volume) buttons.
“HEADPHONE VOLUME” can be used.
STEREO / I • II
When you are viewing a bilingual broadcast
programme, you can choose the sound from
Bilingual I (Sub I) or Bilingual II (Sub II). If
you have poor reception on a stereo
broadcast, you can change from stereo to
mono sound so that you can hear the
broadcast more clearly and easily.
3D CINEMA SOUND
Press the 3 button to set the 3D CINEMA
SOUND effect when 3D CINEMA SOUND
is set to ON or MONO.
Choose 3D CINEMA SOUND. Then
press the a or 3 button to display
the sub-menu.
s: Stereo sound
v : mono sound
> 3D CINEMA SOUND
t : Bilingual I (sub I)
u : Bilingual II (sub II)
SURROUND
BASS BOOST
MID
MID
OK
• The sound mode you can choose differs
depending on the TV programme.
• This function does not work in the EXT
modes.
D0111-EN
„ SURROUND
Adjust the surround effect.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the surround
effect and choosing HIGH will increase the
surround effect.
BASS
You can adjust the low tone of the sound.
2 :weaker
3 : strong
„ BASS BOOST
Adjust the bass sound.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the bass sound
and choosing HIGH will increase the bass
sound.
TREBLE
You can adjust the high tone of the sound.
2 :weaker
3 : strong
30
FEATURES menu
To cancel the SLEEP TIMER
function:
Press the 2 button to set the period of
time to “OFF”.
FEATURES
SLEEP TIMER
CHILD LOCK
APPEARANCE
BLUE BACK
TYPE A
ON
CHILD LOCK
OK
When there is a TV channel you do not want
your children to watch, you can use the
CHILD LOCK function to lock out the TV
channel. Even when a child chooses a
programme number (PR) for a locked TV
channel the screen will change to blue and
display n (CHILD LOCK) so the TV channel
cannot be viewed. Unless you enter a pre-set
ID number by a special operation, the lock
cannot be released and the child cannot view
the TV channel.
D0023-EN
SLEEP TIMER
You can set the TV to automatically turn off
after a set period of time.
1 Choose SLEEP TIMER. Then press
the a or 3 button
A Sub-menu of the SLEEP TIMER
function appears.
„ To set the CHILD LOCK function
> SLEEP TIMER
1 Choose CHILD LOCK, then press
the 0 button
0
120
OFF
“SET ID NO.” (ID number setting screen)
appears.
OK
>> SET ID NO.
D0024-EN
0040
2 Press the 5 buttons to set the
period of time.
OK
Then press the a button
You can set the period of time for up to
120 minutes (2 hours) in 10 minute steps.
• One minute before the SLEEP TIMER
function turns off the TV, “GOOD
NIGHT!” appears.
• The SLEEP TIMER function cannot
be used to turn off the TV’s main
power.
• When the SLEEP TIMER function is
on, you can display the sub-menu of
the SLEEP TIMER function again to
confirm or change the remaining
period of time of the SLEEP TIMER
function. Press the a button to leave
the menu after confirming or changing
the remaining time.
D0025-EN
2 Set the ID number to your liking
1 Press the 6 buttons to choose
a number.
2 Press the 5 buttons to move
the cursor.
3 Press the a button
The Sub-menu of CHILD LOCK appears.
> CHILD LOCK
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
LOCK
OK
D0026-EK
31
FEATURES menu
If you have forgotten the ID
number:
Perform step 1 of “To set the CHILD
LOCK function”. After confirming the ID
number, press the b button to exit the
menu.
4 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) changes, and the
picture of the TV channel registered in the
Programme number (PR) is displayed on
the screen.
• Even if you reset the lock temporarily,
it does not mean that the CHILD
LOCK function set for the TV channel
is cancelled. The next time anyone
tries to view the TV channel, it will be
locked again.
• When you want to cancel the CHILD
LOCK function, you must perform the
operation “To set the CHILD LOCK
function” again.
5 Press the blue button and set the
CHILD LOCK function.
Then press the a button
n (CHILD LOCK) appears and the TV
channel is locked.
To reset the CHILD LOCK function:
Press the blue button again.
n (CHILD LOCK) disappears.
• To stop it being easy to choose the
programme number (PR) of a locked
TV channel, the programme number
(PR) has been set so that it cannot be
chosen with the 6 buttons or the
buttons of the TV.
To disable easy resetting of the CHILD
LOCK function, the menu disappears if
you choose the CHILD LOCK function
and press the a button.
• To stop it being easy to reset the lock,
“ID NO.” (ID No. input screen) is set
so that it cannot appear unless you
„ To view a locked TV channel
1 Choose a programme number (PR)
of a locked TV channel with the
number buttons or PR LIST
The screen changes to blue and the n
(CHILD LOCK) appears. You cannot
view the TV channel.
press the
(Information) button.
h
APPEARANCE
Press the 5 button and choose the format
in which the channel number is displayed
from the three types: TYPE A, TYPE B and
TYPE C.
5
D0027-EN
2 Press the
(Information) button to
h
display “ID NO.” (ID No. input
screen)
BLUE BACK
5
You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is no
input from an external device.
ID NO.
:
D0028-EN
3 Press the number buttons to enter
the ID number
ON:
This function is turned on.
The lock is temporarily released so you
can view the TV channel.
OFF:
This function is turned off.
32
SET UP menu
SET UP
EDIT/MANUAL
AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
PICTURE TILT
DECODER(EXT-2)
EXT SETTING
The EDIT/MANUAL functions are divided
into two types:
• editing the current programme numbers
(PR) (EDIT functions); and
ON
• manually storing a TV channel you want
to view on a particular programme
number (PR) (MANUAL function).
OK
D0029-EN
Here are the details about these functions:
AUTO PROGRAM
MOVE:
This function changes the programme
number (PR) of a TV channel.
You can again perform the AUTO
PROGRAM function TV channel automatic
registration which was performed in the
“Initial settings” (page 8).
To receive SKY 1 you need a satellite tuner.
You must have the satellite tuner set to SKY
1 before starting the AUTO PROGRAM
function.
ID:
This function registers a channel name (ID)
to a TV channel.
INSERT:
This function adds a new TV channel in the
current programme numbers (PR) list by
using the CH number.
• You cannot use the INSERT function if
you do not know the channel number of a
TV channel. Use the MANUAL function
to register a TV channel in the programme
number (PR).
1 Choose AUTO PROGRAM, then
press the a or 3 button
The COUNTRY menu appears as a sub-
menu of the AUTO PROGRAM function.
There are two COUNTRY menus.
Pressing the yellow button changes the
COUNTRY menu as follows:
DELETE:
This function deletes a TV channel you do
not want to list.
> COUNTRY
MANUAL:
This function manually stores a new TV
channel in a programme number (PR).
START
Caution
OK
MORE
• Using the MOVE, DELETE or INSERT
functions rewrites the current programme
numbers (PR) list. Therefore, the
> COUNTRY
programme numbers (PR) of some of the
TV channels will change.
• Using the MANUAL function for a TV
channel for which the CHILD LOCK
function has been set cancels the CHILD
LOCK function for that channel.
START
OK
• Using the MANUAL function for a TV
channel for which the DECODER (EXT-2)
function has been set to ON returns the
setting of the DECODER (EXT-2) function
for that channel to OFF.
• When a TV channel has already been
registered in PR 99, using the INSERT
function deletes that TV channel.
MORE
D0003-EN
2 Press the 5 and 6 buttons to
choose the country where you are
3 Perform steps 5 and 6 of the “Initial
settings” (page 9)
33
SET UP menu
• The CH/CC number is a number
unique to the TV and corresponds to
the channel number of a TV channel.
For the relationship between a channel
number and a CH/CC number, see
“CH/CC NUMBER” on page 37.
„ Basic operation
1 Choose EDIT/MANUAL, then press
the a or 3 button
The EDIT menu appears.
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
„ MOVE
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
1 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
programme number (PR) changes and the
picture of the TV channel stored in the
programme number (PR) appears on the
screen.
ID
MANUAL
OK
MOVE
INSERT DELETE
D0038-EK
2 Follow the description for the
function you want to use
2 Press the 3 button to start the
MOVE function
> EDIT
3 Press the a button to complete
the settings
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
CH 21
The T-V LINK menu appears.
BBC2 CH 22
ITV
CH4
CH5
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
T-V LINK
DOWNLOAD TV
VCR
OK
STORE
OK
D0030-EK
EXIT
D0005-EN
3 Press the 6 buttons to choose a
If you do not have a T-V LINK
compatible VCR connected:
Press the b button to exit the T-V LINK
menu.
new programme number (PR)
To cancel the MOVE function:
Press the b button.
The T-V LINK menu disappears.
4 Press the 2 button to change the
programme number (PR) of a TV
channel to a new programme
number (PR)
If you have a T-V LINK compatible
VCR connected to the EXT-2 terminal:
Follow “Downloading the data to VCR” on
page 11 to transmit the programme number
(PR) data.
• For programme number PR 0, “AV”
appears in the programme numbers (PR)
list.
• An EXT terminal number does not appear
in the programme numbers (PR) list.
34
SET UP menu
„ DELETE
4 Press the blue button to display the
ID LIST (channel name list)
1 Press the 6 buttons to choose a
TV channel
> EDIT
Every time you press the 6 buttons, the
programme number (PR) changes and the
picture of the TV channel stored in the
programme number (PR) appears on the
screen.
CH
ID LIST
M6
MBC
MCM
MDR
MOVIE
MTV
PR
AV
01
02
03
04
05
06
07
08
09
ID
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
MTV3
M
2 Press the yellow button to delete
the TV channel
OK
D0033-EK
The TV channel is deleted from the
programme numbers (PR) list.
5 Press the 6 buttons to choose
the channel name (ID)
„ ID
To cancel the ID function:
Press the b button.
1 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
programme number (PR) changes and the
picture of the TV channel stored in the
programme number (PR) appears on the
screen.
6 Press the a button to give a
channel name (ID) to a TV channel
• You can give your own unique channel
name (ID) to the TV channel. When
you have finished step 3, do not go to
step 4. Press the 5 buttons to move
the cursor, and press the 6 buttons
to choose each character of the channel
name (ID). Then press the a button
to register the channel name (ID) to the
TV channel.
2 Press the red button to start the ID
function
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
Before performing INSERT or
MANUAL operation
ID LIST
OK
• If you register the TV channel (SECAM-
L system) from a French station, be sure
to set the COUNTRY setting to
FRANCE. If the COUNTRY setting is
not set to FRANCE, perform steps 1 and 2
of the “AUTO PROGRAM” (page 33)
procedure and set the COUNTRY setting
to FRANCE before pressing the a
button.
• A CH/CC number unique to this TV and
corresponding to the Channel number of a
TV channel is required. Find the
corresponding CH/CC number from a
table “CH/CC NUMBER” on page 37
based on the Channel number of the TV
channel.
D0031-EK
3 Press the 6 buttons to choose
the first character of a channel
name (ID) you want to give the TV
channel
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
M
ID LIST
OK
D0032-EK
35
SET UP menu
• When the COUNTRY setting is not
FRANCE, use a two-digit CH/CC
number. When the COUNTRY setting is
FRANCE, use a three-digit CH/CC
number.
„ MANUAL
1 Press the 6 buttons to choose a
programme number (PR) for a new
TV channel
„ INSERT
2 Press the blue button to activate
the MANUAL function
1 Press the 6 buttons to choose a
programme number (PR) for which
you will register a new TV channel
> MANUAL
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
2 Press the green button and start
the INSERT function
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH
SEARCH+
FINE-
OK
BBC1
BBC2
ITV
CH4
CH5
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
FINE+
SEARCH-
D0035-EK
To cancel the MANUAL function:
Press the b button.
When the COUNTRY setting is
IRELAND:
OK
0
9
CH/CC
D0034-EK
At the right side following the CH/CC
number, the SYSTEM (broadcasting
system) of the TV channel appears.
To cancel the INSERT function:
Press the b button.
3 When the COUNTRY setting is
UNITED KINGDOM:
3 When the COUNTRY setting is
UNITED KINGDOM:
Press the number buttons to enter
the remaining CH number
• You cannot enter CC numbers.
When the COUNTRY setting is
IRELAND:
Press the 6 buttons to choose
“CH” or “CC”, then enter the
remaining CH or CC number
Continue to step 4
When the COUNTRY setting is
IRELAND:
Press the 3 button to choose the
SYSTEM (broadcasting system) for
a TV channel you want to register
If you do not know the correct
broadcasting system, set the SYSTEM to
“I”. If “I” is not correct, you will not hear
the sound normally when the TV detects a
TV channel. In this case, retry to set the
SYSTEM correctly so that no problem
arises.
The TV shifts to registration mode.
When the registration is completed, the
picture of the TV channel appears on the
screen.
• The CH/CC number is a number given
to each broadcast frequency that
carries a TV channel. If the TV cannot
detect the TV channel corresponding
to the broadcast frequency indicated
by the CH/CC number, a “no-signal”
picture appears.
4 Press the green or red button to
search for a TV channel
Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.
36
SET UP menu
CH
Channel
E2, IR A
E3, IR B
E4, IR C
E5, IR D
E6, IR E
E7, IR F
E8, IR G
E9
CH
Channel
E40
E41
E42
E43
E44
E45
E46
E47
E48
E49
E50
E51
E52
E53
E54
E55
E56
E57
E58
E59
E60
E61
E62
E63
E64
E65
E66
E67
E68
E69
5 Press the green or red button
repeatedly until the TV channel you
want appears
CH 02
CH 03
CH 04
CH 05
CH 06
CH 07
CH 08
CH 09
CH 10
CH 11
CH 12
CH 21
CH 22
CH 23
CH 24
CH 25
CH 26
CH 27
CH 28
CH 29
CH 30
CH 31
CH 32
CH 33
CH 34
CH 35
CH 36
CH 37
CH 38
CH 39
CH 40
CH 41
CH 42
CH 43
CH 44
CH 45
CH 46
CH 47
CH 48
CH 49
CH 50
CH 51
CH 52
CH 53
CH 54
CH 55
CH 56
CH 57
CH 58
CH 59
CH 60
CH 61
CH 62
CH 63
CH 64
CH 65
CH 66
CH 67
CH 68
CH 69
If the TV channel reception is poor:
Press the blue or yellow button to fine-
tune the TV channel.
E10, IR H
E11, IR J
E12
6 Press the a button and register
the TV channel to a Programme
number (PR)
E21
E22
E23
The normal EDIT menu is resumed.
E24
E25
„ CH/CC NUMBER
E26
E27
• When you want to use the INSERT
function on page 36, find the CH/CC
number corresponding to the channel
number of the TV channel from this table.
If you want to know a particular TV
channel’s channel menu, look in TV
listings magazines or contact the
broadcaster.
• When the COUNTRY setting is UNITED
KINGDOM, the CC number channels and
the channels from CH/CC 02 to CH/CC 12
cannot be received.
E28
E29
E30
E31
E32
E33
E34
E35
E36
E37
E38
E39
CC
Channel
S1
CC
Channel
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
X
CC 01
CC 02
CC 03
CC 04
CC 05
CC 06
CC 07
CC 08
CC 09
CC 10
CC 11
CC 12
CC 13
CC 14
CC 15
CC 16
CC 17
CC 18
CC 19
CC 20
CC 21
CC 22
CC 23
CC 24
CC 25
CC 26
CC 27
CC 28
CC 29
CC 30
CC 31
CC 32
CC 33
CC 34
CC 35
CC 36
CC 37
CC 38
CC 39
CC 40
CC 41
CC 75
CC 76
CC 77
CC 78
CC 79
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
Y
Z
Z+1
Z+2
37
SET UP menu
LANGUAGE
DECODER (EXT-2)
The LANGUAGE setting which was
performed in the “Initial settings” (page 8)
can be changed.
If you have a decoder connected to a T-V
LINK compatible VCR, which in turn is
connected to the EXT-2 terminal, use the
DECODER (EXT-2) function to unscramble
the scrambled TV channels.
1 Choose LANGUAGE, then press
the a or 3 button
1 Turn on the decoder power
A sub-menu of the LANGUAGE function
appears.
2 Display the scrambled TV channel
on the TV
> LANGUAGE
Even if the decoder is working, a
scrambled picture appears.
3 Display the SET UP menu and
choose DECODER (EXT-2)
OK
SET UP
D0002(E)-EN
AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
PICTURE TILT
DECODER(EXT-2)
EXT SETTING
2 Press the 5 and 6 buttons to
choose a language. Then press the
a button
ON
OK
PICTURE TILT
D0029-EN
There are cases where the Earth’s magnetic
field may make the picture tilt or make
unnatural colours appear in the corner of the
screen. If this happens, you can correct it.
4 Press the 5 buttons to choose
ON
An unscrambled picture appears.
1 Choose PICTURE TILT, then press
the a or 3 button
To cancel the DECODER (EXT-2)
function:
Press the 5 buttons to choose OFF.
The sub-menu of the PICTURE TILT
function appears.
5 Press the a button to complete
the setting
>> PICTURE TILT
The T-V LINK menu appears.
T-V LINK
DOWNLOAD TV
VCR
OK
D0018-EN
OK
2 Press the 6 buttons until the
picture becomes level. Then press
the a button
EXIT
D0005-EN
You can send the programme numbers
data to a VCR with the T-V LINK
function.
38
SET UP menu
6 Turn on the VCR, and then press
the a button to transmit the data
to VCR
EXT SETTING
1 Choose EXT SETTING, then press
the a or 3 button
The T-V LINK menu disappears once the
data transmission ends.
The EXT SETTING menu appears.
7 If you have another TV channel
capable of being unscrambled with
a Decoder, repeat steps 2 to 6
> EXT SETTING
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
If the DECODER (EXT-2) function has
been set to “ON” but the TV channel
cannot be unscrambled, check the
following:
EXT-4
ID LIST
• Has the decoder been connected to the
VCR properly according to the VCR
and decoder instruction manuals?
• Has the decoder power been turned
on?
OK
S-IN
D0020-EN
2 Follow the instructions for the
function you want to use and
operate the function
• Can the TV channel be unscrambled
with a decoder?
S-IN:
• Do you need to change the VCR
settings in order to connect the
decoder? Confirm that the VCR is set
properly by rechecking the VCR
instruction manual.
You can enjoy the high-quality picture of
the 2 S-VIDEO signal (Y/C signal).
ID LIST:
You can have a name for each of the
devices connected for each EXT terminal.
DUBBING:
You can choose a signal source to be
output from an EXT-2 terminal.
„ S-IN (S-VIDEO input)
You can connect a device (such as an S-VHS
VCR) to enjoy the high-quality picture of the
S-VIDEO signal (Y/C signal).
Preparation:
• First read the device’s instruction manual
and “Additional preparation” on page 42
to connect the device to the TV properly.
Second, follow the device’s instruction
manual to set the device so that it sends an
S-VIDEO signal (Y/C signal) to the TV.
• Do not set S-IN (S-VIDEO input) to an
EXT terminal connected to a device
which cannot output an S-VIDEO (Y/C
signal). If it is set wrongly, a picture
cannot appear.
39
SET UP menu
„ ID LIST
1 Press the 5 or 6 buttons to
You can store a name for each of the devices
connected to each EXT terminal. Giving a
name to an EXT terminal makes the EXT
terminal number appear on the screen,
together with its name.
choose an EXT terminal
> EXT SETTING
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
1 Press the 5 or 6 buttons to
choose an EXT terminal
EXT-4
2 Press the blue button to display the
name list (ID LIST)
ID LIST
OK
S-IN
> EXT SETTING
D0110-EN
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
ID LIST
VHS
2 Press the yellow button and set the
S-IN (S-VIDEO input).
S-VHS
DVC
CAM
SAT
Then press the a button
STB
EXT-4
GAME
DVD
DVR
An S-IN (S-VIDEO input) mark is
displayed. You can view an S-VIDEO
signal (Y/C signal) instead of the regular
video signal (composite signal).
OK
D0021-EN
To cancel the S-IN (S-VIDEO input)
setting:
Press the yellow button and turn off S-IN (S-
VIDEO input) mark. The regular video
signal (composite signal) pictures are
resumed.
3 Press the 6 buttons to choose a
name. Then press the a button
The ID LIST disappears and the name is
assigned to the EXT terminal.
• You cannot assign an EXT terminal
name not found in the name list (ID
LIST).
• The EXT-1 terminal does not support S-
VIDEO signal (Y/C signal) and you
cannot set S-IN (S-VIDEO input) in the
EXT-1 terminal.
To erase a name assigned to the
EXT terminal:
Choose a blank space.
• Setting S-IN (S-VIDEO input) changes
the head character from “E” to “S”. When
an EXT terminal receives a normal video
signal, “E1”, “E2”, “E3” or “E4” appears
on the display. This changes to “S2”, “S3”
or “S5” when it receives an S-VIDEO
signal.
4 Press the a button to complete
the setting
• Even a device which can output an
S-VIDEO signal (Y/C signal) may output
a regular video signal (composite signal)
depending on the device setting. If a
picture cannot appear because the S-IN
(S-VIDEO input) setting has been made,
read the device instruction manual
carefully again to check for the device
settings.
40
SET UP menu
TV:
„ DUBBING
The picture and sound of the TV channel
you are currently viewing are output from
the EXT-2 terminal.
You can choose a signal source to be output
from the EXT-2 terminal.
You can do this with the output signals of the
devices connected to other EXT terminals, or
with the picture and sound from a TV
channel you are currently viewing.
• During dubbing, you cannot turn off
the TV. Turning off the TV also turns
off the output from the EXT-2
terminal.
1 Press the 5 buttons to choose
• When you choose an EXT terminal as
an output, you can view a TV
programme or a picture from the other
EXT terminal while dubbing the
picture from a device connected to the
EXT terminal onto a VCR connected
to the EXT-2 terminal.
the arrow from the menu
> EXT SETTING
EXT-1
EXT-3
EXT-5
TV
DUBBING
EXT-2
EXT-4
• The RGB signals from TV games
cannot be output. Teletext programmes
cannot be output.
OK
D0022-EN
2 Press the 6 buttons to choose an
EXT terminal or TV.
Then press the a button
The arrow in the menu represents a signal
flow. The left side of the arrow shows a
signal source output from the EXT-2
terminal.
EXT-1/EXT-3/EXT-5:
The output signal of the device connected
to an EXT terminal passes through the TV
and is output from the EXT-2 terminal.
41
Additional preparation
Connecting external equipment
Connect the equipment to the TV, making
the correct rear panel and front panel
connections.
1 VCR (composite signal)
2 VCR (composite signal/S-VIDEO signal)
3 T-V LINK compatible VCR (composite
signal/S-VIDEO signal)
4 Decoder
5 DVD player (composite signal/S-VIDEO
signal)
Before connecting anything:
• Read the manuals that came with the
equipment.
Depending on the equipment, the
connection method may be different from
the diagram. Also, the equipment settings
may need to change depending on the
connection method.
6 DVD player (composite signal/RGB
signal)
7 DVD player (component video signals;
Pr/Pb/Y)
8 TV game (composite signal/RGB signal)
9 TV game (composite signal/S-VIDEO
signal)
0 Headphones
- Camcorder (composite signal/S-VIDEO
signal)
= SCART cable
~ Audio cable
! Video cable
@ S-VIDEO cable
# Component cable
• Turn off all the equipment including the
TV.
• The “Specifications” on the back cover
give the details of the EXT terminals. If
you are connecting equipment not listed
in the following connection diagram, see
the table to choose the best EXT terminal.
• Connecting cables are not supplied.
HV-36P38SJE
Front of the TV
S
L
R
P
E
X
T
-
5
S
L
R
P
EXT-5
Back of the TV
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
42
Additional preparation
HV-32P37SJE/HV-28P37SJE
Back of the TV
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT
-2
S
S
R
P
E
X
T
L
EXT-3
5
S
R
L
A
U
D
I
O
O
U
T
R
S
E
X
T
P
L
5
R
Back of the TV
EXT-
4
EXT-1
Y
Pb
Pr
L
EXT-2
S
R
EXT-3
S
L
AUDIO OUT
R
43
Additional preparation
„ Equipment which can output the
S-VIDEO signal (Y/C signal) such
as an S-VHS VCR
„ TV output from the EXT-1 terminal
The video/sound signal of a TV channel you
are viewing is always output from the EXT-1
terminal.
Connect the equipment to an EXT terminal
(but not the EXT-1 terminal).
• Changing over a programme number (PR)
also changes over the TV output from the
EXT-1 terminal.
• The video/sound signal from an EXT
terminal cannot be output.
You can choose between an S-VIDEO signal
(Y/C signal) and a regular video signal
(composite signal). For details of how to
operate the equipment, see “S-IN (S-VIDEO
input)” on page 39.
• Teletext programmes cannot be output.
„ Connecting speakers/amplifier
While referring to the audio equipment
connection diagram, connect the audio
equipment you want to the TV.
„ T-V LINK compatible VCR
Be sure to connect the T-V LINK compatible
VCR to the EXT-2 terminal. If not, the T-V
LINK function will not work properly.
• When connecting a T-V LINK compatible
VCR to the EXT-2 terminal, be sure to
connect the decoder to the VCR. If not,
the T-V LINK function may not work
properly. After you have stored TV
You can use external front speakers to listen
to the TV sound instead of the TV speakers.
Before connecting anything:
• Read the manuals provided with the
amplifier and speakers.
channels in the programme numbers (PR)
list, set the DECODER (EXT-2) function
for the programme number (PR) to ON to
unscramble a scrambled TV channel. For
details, see “EXT SETTING” on page 39.
• Turn the TV and amplifier off.
• To prevent magnetism from the speakers
adversely effecting the TV screen, use
magnetic-shielded speakers for the front
speakers.
• Note that connecting cables are not
supplied.
„ Connecting headphones
Connect the headphones with a stereo mini-
jack (3.5 mm diameter) to the headphone
socket at the TV rear panel.
Back of the TV
L
R
• No sound comes from the TV speakers
when the headphones are connected and
only one screen is displayed.
„ Video or sound signal output from
the EXT-2 terminal
1
2
Amplifier
Front speakers (Magnetic-shielded type)
You can change over the output of the video/
sound signal from the EXT-2 terminal. This
is useful when you want to dub the video/
sound from another device onto the VCR
connected to the EXT-2 terminal. For details
on how to do this, see “DUBBING” on
page 41.
• The output from the AUDIO OUT
terminal is not interrupted by headphone
connection to the TV. You cannot cut the
sound from the front speaker even if you
connect a headphone to the TV.
• Adjust the volume of the external
speakers with the amplifier.
44
Troubleshooting
If a problem arises while you are using the TV, please read this troubleshooting guide carefully
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may
think there is a problem with the TV itself.
Important:
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you
have a question when you are operating a function, read the page(s) for that function carefully,
not this troubleshooting guide.
• If you follow the advice in this troubleshooting guide without any success, unplug the mains
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to
remove the rear cover of the TV.
–Have the TV and aerial been connected
properly?
–Has the aerial cable been damaged?
–Is the aerial pointing in the right
direction?
„ If you cannot turn on the TV
• Is the mains plug connected to the mains
outlet?
• Is the power lamp lit? If not, press the
main power button.
–Is the aerial itself faulty?
• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV on when the VCR/TV/DVD
switch is set to the VCR or DVD position.
• If the TV or aerial suffers interference
from other equipment, stripes or noise
may appear in the picture. Move any
equipment such as an amplifier, personal
computer, or a hair drier, that can cause
interference away from your TV. Or try
moving the TV. If the aerial suffers
interference from a radio tower or high-
voltage wire, please contact your local
dealer.
• If the TV suffers interference from signals
reflecting from mountains or buildings,
double-pictures (ghosting) will occur. Try
to change the aerial’s direction or replace
it with one with better directionality.
• Are your COLOUR SYSTEM settings
correct? Follow the description
„ If you cannot turn off the TV
• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV off when the VCR/TV/DVD
switch is set to the VCR or DVD position.
„ No picture or no sound
• Have you chosen a TV channel with very
poor reception? If so, the BLUE BACK
function will be activated: the entire
screen becomes blue, and the sound is
muted. If you still want to view the TV
channel, follow the description “BLUE
BACK” on page 32 to change the BLUE
BACK function setting to OFF.
“COLOUR SYSTEM” on page 28 to try
to solve the trouble.
• Have the COLOUR and BRIGHT settings
been adjusted properly? Follow the
description “BRIGHT” and “COLOUR”
on page 26 to try to adjust them properly.
• Videotaping teletext is not recommended
because it may not record correctly.
• When a white and bright still image (such
as a white dress) is displayed on the
screen, the white part may look as if it is
coloured. This is unavoidable due to the
nature of the picture tube itself, and not
due to a TV failure. When the picture
disappears from the screen, the unnatural
colours will also disappear.
• If the SYSTEM setting for a TV channel
is incorrect, it may prevent the sound
from being issued. Follow the description
“EDIT/MANUAL” on page 33 to use the
MANUAL function to try to change the
SYSTEM setting.
„ Poor picture
• If noise (snow) totally blocks out the
picture, there may be a problem with the
aerial or aerial cable. Check the following
to try to solve the problem:
45
Troubleshooting
• When viewing images from commercially
available video software products, or
videos from videotapes which have been
recorded improperly, the top of the image
may be distorted. This is due to the
condition of the video signal. There is
nothing wrong with the TV.
„ Other issues
• When the SLEEP TIMER function
operates, the TV is automatically turned
off. If the TV suddenly turns off, try to
press the # (standby) button to turn on
the TV once again. If the TV goes back to
normal, there is no problem.
• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with 625p
progressive-scanning component signals.
If this occurs, change the output setting of
the connected device to 625i interlace-
scanning component signal output. See
the instructions that came with the device
for more information.
• When the TV is receiving a wide-screen
signal (WSS) or a signal from an external
device affecting the screen size, the
ZOOM mode automatically changes.
When you want to resume the previous
ZOOM mode, press the c button
again.
• If you bring magnetised equipment such
as a speaker near to your TV, the picture
may be warped or unnatural colours may
appear at the corners of the screen. In this
case, keep the equipment away from your
TV. If speakers cause this to happen, use
magnetically-shielded speakers instead.
• A picture may be tilted due to the earth’s
magnetic field. If so, use the “PICTURE
TILT” on page 38 to correct the tilt.
• It takes a short period of time from the
time an operation such as changing
channels is performed until an image is
displayed. This is not a fault. This is the
time needed for the image to stabilize
before it can be displayed.
„ Poor sound
• Have you adjusted BASS or TREBLE
properly? If not, follow the description
“BASS” or“TREBLE” on page 30.
• When TV channel reception is poor, it can
be hard to hear stereo or bilingual sound.
In this case, follow the description
“STEREO / I • II” on page 30 to hear the
sound more easily by changing it to a
mono sound.
„ If the TV does not respond to the
remote control
• Have the batteries of the remote control
worn out? Follow the description “Putting
the batteries into the remote control” on
page 8 and replace them with new batteries.
• Have you attempted to use the remote
control from the sides or rear of the TV or
from more than seven metres away from the
TV? Use the remote control in front of your
TV or from less than seven metres away.
• When you are viewing a teletext
programme, you cannot operate the
menus. Press the b button to return to
the ordinary TV programme, and then try
operating the menus.
• The TV may make a crackling sound due
to a sudden change in temperature. The
picture or sound may be normal. If you
hear crackling sounds frequently while
you are viewing the TV, there may be
other causes. As a precaution, ask your
service technician to inspect it.
• Touching the screen may cause you to
feel a slight electric shock due to its static
electricity. This is unavoidable due to the
construction of the picture tube. It is not a
problem with the TV. You can rest
assured that this static discharge is not
harmful.
• If the TV suddenly stops responding,
press the main power button on the TV
and turn off the main power. Press the
main power button again to turn on the
TV. If the TV returns to a normal state, it
is not a failure.
• When set to 2-pictures multi, adjust the
headphone sound with HEADPHONE
VOLUME in the SOUND menu.
46
Specifications
Model
HV-36P38SJE
When the COUNTRY setting is When the COUNTRY setting is
UNITED KINGDOM IRELAND
CCIR B/G, I, D/K, L
PAL, SECAM
COUNTRY setting
Broadcasting systems
Colour systems
CCIR I
PAL
• The EXT terminals also support the • The EXT terminals also support the
NTSC 3.58/4.43 MHz system.
NTSC 3.58/4.43 MHz system.
Channels and frequencies
Sound-multiplex systems
Teletext systems
E21-E69
IR A-J, E2-E12, E21-E69, S1-S41, X,
Y, Z, Z+1, Z+2
NICAM (B/G, I, D/K, L) system,
A2 (B/G, D/K) system
FLOF (Fastext), TOP,
WST (World Standard System)
NICAM (I) system
FLOF (Fastext),
WST (World Standard System)
Power requirements
Power consumption
Picture tube size
Audio output
220 - 240 V AC, 50 Hz
141 W (Standby: 2.0 W)
Viewable area 86 cm (measured diagonally)
Rated Power output: TV: 10 W + 10 W, Woofer: 18 W
TV: 2 cm round × 2, (3 cm × 10 cm) oval × 4, Woofer: 16 cm round × 1
Speakers
EXT-1 terminal
Euroconnector (21-pin, SCART)
• Video input, Audio L/R inputs and RGB inputs are available.
• TV broadcast outputs (Video and Audio L/R) are available.
EXT-2 terminal
Euroconnector (21-pin, SCART)
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are
available.
• Video and Audio L/R outputs are available.
• T-V LINK functions are available.
EXT-3 terminal
EXT-4 terminal
Euroconnector (21-pin, SCART)
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
RCA connectors × 5
• Component video (Pr, Pb, Y) inputs (625p, 525p, 1125i) and Audio L/R inputs
are available.
EXT-5 terminal
RCA connectors × 3
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
AUDIO OUT terminal
RCA connectors × 2
• Audio L/R outputs are available.
• Output level 0.5 Vrms.
Headphone jack
Dimensions (W × H × D)
Weight
Stereo mini-jack (3.5 mm in diameter)
TV: 912 mm × 624 mm × 593 mm, Woofer: 435 mm × 230 mm × 120 mm
TV: 70 kg, Woofer: 4 kg
Accessories
Remote control unit × 1 (RM-C1800), Woofer × 1
AA/R6 dry cell battery × 2
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of
the owners of copyright of the original picture sources, as this would be an infringement of
copyright.
47
Model
HV-32P37SJE/HV-28P37SJE
When the COUNTRY setting is
UNITED KINGDOM
When the COUNTRY setting is
COUNTRY setting
IRELAND
Broadcasting systems
Colour systems
CCIR I
PAL
CCIR B/G, I, D/K, L
PAL, SECAM
• The EXT terminals also support the • The EXT terminals also support the
NTSC 3.58/4.43 MHz system.
NTSC 3.58/4.43 MHz system.
Channels and frequencies
Sound-multiplex systems
Teletext systems
E21-E69
IR A-J, E2-E12, E21-E69, S1-S41, X,
Y, Z, Z+1, Z+2
NICAM (B/G, I, D/K, L) system,
A2 (B/G, D/K) system
FLOF (Fastext), TOP,
WST (World Standard System)
NICAM (I) system
FLOF (Fastext),
WST (World Standard System)
Power requirements
Power consumption
220 - 240 V AC, 50 Hz
HV-32P37SJE: 137 W (Standby: 2.0 W)
HV-28P37SJE: 127 W (Standby: 2.0 W)
Picture tube size
HV-32P37SJE: Viewable area 76 cm (measured diagonally)
HV-28P37SJE: Viewable area 66 cm (measured diagonally)
Audio output
Speakers
Rated Power output: 10 W + 10 W
(13 cm × 6.5 cm) oval × 2
EXT-1 terminal
Euroconnector (21-pin, SCART)
• Video input, Audio L/R inputs and RGB inputs are available.
• TV broadcast outputs (Video and Audio L/R) are available.
EXT-2 terminal
Euroconnector (21-pin, SCART)
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are
available.
• Video and Audio L/R outputs are available.
• T-V LINK functions are available.
EXT-3 terminal
EXT-4 terminal
Euroconnector (21-pin, SCART)
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
RCA connectors × 5
• Component video (Pr, Pb, Y) inputs (625p, 525p, 1125i) and Audio L/R inputs
are available.
EXT-5 terminal
RCA connectors × 3
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
AUDIO OUT terminal
RCA connectors × 2
• Audio L/R outputs are available.
• Output level 0.5 Vrms.
Headphone jack
Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D)
HV-32P37SJE: 948 mm × 562 mm × 550 mm
HV-28P37SJE: 854 mm × 508 mm × 493 mm
Weight
HV-32P37SJE: 54.0 kg
HV-28P37SJE: 38.0 kg
Accessories
Remote control unit × 1 (RM-C1800)
AA/R6 dry cell battery × 2
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of
the owners of copyright of the original picture sources, as this would be an infringement of
copyright.
LCT1536-001A-U
0903-T-CR-JMUK
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
|
Jenn Air 20" User Manual
JVC AV 21MF11SPF User Manual
JVC AV 32230 User Manual
Miele GAS COMBISET CS 1011 User Manual
NEC PX 42XR3A User Manual
Nuvo V1360A User Manual
Philips 21PT2683 User Manual
Philips 107S63 User Manual
Philips 221E User Manual
Philips CD360 User Manual